BMW 65 90 0 028 873 Installation Instructions Manual Download

Page: 1 / 22

Power

NAVIGATION COMPU

ON COMPUTER

VDO a

O ayt

yton

Power

NAVIGATION COMPUTER

VDO ayton

F 46 1090 B

Mark III navigation system retrofit kit

(System with colour monitor and control in the centre console,
navigation computer in the boot)

BMW 3 Series Saloon (E 46/4) LHD
BMW 3 Series Coupé (E 46/2) LHD

Specialist and electrical knowledge required.

The installation time is 3 – 4 hours, but this may vary depending on the condition of the car
and the equipment in it.

Retrofit/Installation kit No. 65 90 0 151 635

65 90 0 028 873

BMW Parts and Accessories
Installation Instructions

Retrofit/Installation kit No. 65 90 0 151 635 (others see cover sheet)

Issue date: 06.2002

Installation instructions No. 01 29 0 028 872

Summary of Contents for 65 90 0 028 873























Search results

Summary of Contents for 65 90 0 028 873

Reviews:

Related manuals for 65 90 0 028 873

Brands by name

Popular brands

BMW 65 90 0 028 873, Installation Instructions Manual

Search results

Summary of Contents for 65 90 0 028 873

Reviews:

Related manuals for 65 90 0 028 873

Brands by name

Popular brands