Wireless Remote Keypad (KP-S3)
P
P
a
a
r
r
t
t
s
s
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
1. Active LED (Green)
2. Transmission LED (Red)
3. Fault LED (Orange)
4. Away Arm Key
5. Home Arm Key
6.
Key
7. Disarm Key
8. Mounting Hole Cover
9. Panic Alarm
Press both 1 and 3 key to trigger Panic alarm
10. Fire Alarm
Press both 4 and 6 key to trigger Fire alarm
11. Emergency Alarm
Press both 7 and 9 key to trigger Emergency alarm
12. Mounting Holes
13. Tamper Switch
The Tamper switch protects the PIR from unauthorized cover
opening or removal from mounted surface.
14. Battery Insulator
P
P
a
a
c
c
k
k
a
a
g
g
e
e
C
C
o
o
n
n
t
t
e
e
n
n
t
t
1 x Remote Keypad
2 x wall plugs and screws
1 x CR2450 3V lithium battery (pre-installed)
For learning the Remote Keypad:
1. Pull out the battery insulator to activate battery.
2. Put the Control Panel into learning mode.
3. Press both
#
and
keys to transmit learn code
4. Refer to Control Manual to complete the learning process.
The Remote Keypad has 2 mounting holes which are covered
from the front for wall mounting.
1. Lift the mounting hole cover to reveal the 2 mounting holes.
2. Use the two mounting holes to mark position on the wall at
chest height.
3. Drill holes into the wall in marked location.
4. Fix the keypad onto the wall with the screw and plugs
provided.
5. Replace the mounting hole covers.
S
S
t
t
a
a
n
n
d
d
b
b
y
y
M
M
o
o
d
d
e
e
The Remote Keypad features a power saving feature. When no
key is pressed for 5 seconds, the Remote Keypad will turn off
automatically to conserve power. When any key is pressed, the
Remote Keypad will wake up and turn on Active LED to indicate it
is now under normal operation
K
K
e
e
y
y
p
p
a
a
d
d
S
S
e
e
t
t
t
t
i
i
n
n
g
g
The Remote Keypad features a Test (programming) mode for you
to customize its setting. Before you start using the Remote
Keypad, you should first finish configuration setting.
The Remote Keypad also feature a Keypad PIN code which is
used to access the Test mode, To enter Test Mode, Enter
“
0000
”(Default Keypad PIN code) + “
＊
”
key, the Active LED will
begin to flash to indicate Keypad is now under Test Mode.
Under Test Mode, the following functions include:
Key
Function
“
＊
” + “1”
Transmit learn code (same as pressing
both
#
and
keys under normal mode)
“
＊
” + “2”
Enable dual key Panic Alarm function
“
＊
” + “3”
Enable dual key Fire Alarm function
“
＊
” + “4”
Enable dual key Medical Alarm function
“
＊
” + “5”
Disable all dual key functions (
Default
)
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Remove
Remove
Mounting Hole
Mounting Hole
