background image

GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS

WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS

. Failure to follow all

instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

Keep your work area clean and well lit.

Cluttered benches and dark areas invite

accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. 

Power tools create sparks which may ignite the dust

or fumes.

• Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

• Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from

heat, oil, sharp edges or moving parts. Replace damaged cords immediately.

Damaged cords may create a fire.

• A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery. 

A charger that may be

suitable for one type of battery may create a risk of fire when used with another battery.

• Use battery operated tool only with specifically designated battery pack. 

Use of any

other batteries may create a risk of fire.

Personal Safety

• Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication.

A moment of inattention while operating power tools may result in serious

personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing , and gloves away from moving parts.

Loose clothes, jewelry, or long hair

can be caught in moving parts. Air vents cover moving parts and should be avoided.

• Avoid accidental starting. Be sure switch is in the locked or off position before

inserting battery pack.

Carrying tools with your finger on the switch or inserting the

battery pack into a tool with the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on.

A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. 

Proper footing and

balance enable better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

• Use clamps or other practical way to secure and support the workpiece to a stable

platform.

Holding the work by hand or against your body is unstable and may lead to loss

of control.

• Do not force tool. Use the correct tool for your application.

The correct tool will do the

job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off.

A tool that cannot be controlled with

the switch is dangerous and must be repaired.

• Disconnect battery pack from  tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tool.

Such

preventative safety measures reduce the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. 

Tools are

dangerous in the hands of untrained users.

• When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws or other small metal objects that can make a
connection from one terminal to another. 

Shorting the battery terminals together may

cause sparks, burns, or a fire.

• Maintain tools with care. Keep cutting tools sharp and clean. 

Properly maintained

tools, with sharp cutting edge are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced
before using.

Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may create a risk of injury when used on
another tool.

Service

• Tool service must be performed only by qualified repair personnel. 

Service or

maintenance performed by unqualified personnel may result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual.

Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of shock or injury.

Additional Specific Safety Rules

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring. 

Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the operator.

Wear safety goggles or other eye protection.

Hammering and drilling operations cause

chips to fly. Flying particles can cause permanent eye damage.

Bits, sockets and tools get hot during operation.

Wear gloves when touching them.

Do not operate this tool for long periods of time.

Vibration caused by tool action may

be harmful to your hands and arms. Use gloves to provide extra cushion and limit expo-
sure by taking frequent rest periods.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and 
• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. 

Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals. 

WARNING: Use of this tool can generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury.

Always use NIOSH/OSHA approved

respiratory protection appropriate for the dust exposure. Direct particles away from face and
body.

CAUTION: When not in use, place tool on its side on a stable surface where it will not

cause a tripping or falling hazard. 

Some tools with large battery packs will stand upright on

the battery pack but may be easily knocked over. 

CAUTION: Wear appropriate personal hearing protection during use. 

Under some

conditions and duration of use, noise from this product may contribute to hearing loss.
• The label on your tool may include the following symbols. The symbols and their defini-

tions are as follows:

V ..........volts

A ..........amperes

Hz ........hertz

W ..........watts

min ......minutes

........alternating current

....direct current

no ........no load speed

........Class II Construction

…/min ..revolutions 

........earthing terminal

..............

per minute

........safety alert symbol

BPM......beats per minute

Battery Cap Information

Battery storage and carrying caps are provided for use whenever the battery is out of the
tool or charger. Remove cap before placing battery in charger or tool.

WARNING!

Do not store or carry battery so that metal objects can contact exposed

battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product
kit boxes, drawers, etc. with loose nails, screws, keys, etc. without battery cap. Without cap
in place, battery could short circuit causing fire or burns or damage to battery.

INSTRUCTION MANUAL

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. 

ADVERTENCIA: 

LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO. 

CAT. NO. BDID1202      FORM NO. 5106173-00      Copyright © 2004 Black & Decker

(MAY-04)      Printed in China

1

1

1

1

2

2

2

2

  

  

V

V

V

V

o

o

o

o

ll

ll

tt

tt

  

  

C

C

C

C

o

o

o

o

rr

rr

d

d

d

d

ll

ll

e

e

e

e

ss

ss

ss

ss

  

  

II

II

m

m

m

m

p

p

p

p

a

a

a

a

cc

cc

tt

tt

  

  

D

D

D

D

rr

rr

ii

ii

vv

vv

e

e

e

e

rr

rr

B E F O R E   R E T U R N I N G   T H I S   P R O D U C T  

F O R   A N Y   R E A S O N   P L E A S E   C A L L

1 - 8 0 0 - 5 4 4 - 6 9 8 6

IF YOU SHOULD HAVE A QUESTION OR 

EXPERIENCE A PROBLEM WITH YOUR 

BLACK & DECKER PRODUCT,

C A L L   1 - 8 0 0 - 5 4 4 - 6 9 8 6

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE

No., AND DATE CODE (e.g. 0130M). IN MOST CASES, A

BLACK & DECKER 

REPRESENTATIVE

CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COM-

MENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

Cat. No. BDID1202

1

2

Variable Speed 

Switch

Interrupteur à vitesse

variable

Conmutador de

velocidad variable

Forward/Reverse

Button

Bouton de 

commande de
marche avant ou
marche arrière

Botón de avance y

reversa

Safety Warnings and Instructions: Charging 

1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary markings on (1) 

battery charger, (2) battery, and (3) product using battery.

3.

CAUTION:

To reduce the risk of injury, charge only Black & Decker Battery Packs.

Other types of batteries may burst causing personal injury and damage.

4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by Black & Decker may result in a risk

of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round 

jacketed extension  cords should be used, and we recommend that they be listed by
Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord 
must be suitable for outdoor use. Any cord marked for outdoor use can also be used 
for indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is 
suitable for outdoor use.

Battery Cap

Summary of Contents for 5106173-00







Reviews: