background image

1 6 9 8 1  Ser ies

Assembly

Operation

Safety

Storage

SmartClean

®

System pre-treats,

loosens, and lifts out dirt.

Sm artTem p

heats solution for 

best cleaning

On-board DirtLifter

®

TurboBrush

DirtLifter

®

PowerBrush lifts deep 

down dirt, groom s carpet

Sm artMix

®

auto-adjusts 

form ula for every cleaning job

Tank-in-Tank

is easy to use - 

saves trips to em pty and refill

ReadyTools

instantly converts 

from  floor cleaning to tools

User’s Guide

Thanks for buy ing a POWERSTEAMER

®

PROHEAT

PLUS Heated Solution Deep Cleaner.

We’re glad you purchased a BISSELL POWERSTEAMER

®

PROHEAT

PLUS Heated Form ula Deep Cleaner. Everything we 

know about floor care went into the design and construction 

of this com plete, high-tech hom e cleaning system .

Your POWERSTEAMER

®

PROHEAT

PLUS is well m ade, 

and we back it with a full one-year warranty. We also stand 

behind it with a knowledgeable, dedicated Consum er 

Services departm ent, so, should you ever have a problem , 

you’ll receive fast, considerate assistance.

My great-grandfather invented the floor sweeper 

in 1876. Today, BISSELL is a global leader in the design, 

m anufacture, and service of high 

quality hom ecare products like 

your POWERSTEAMER

®

PROHEAT

PLUS.

Thanks again, from

all of us at BISSELL.

Mark J. Bissell

President and Chief Executive Officer

Summary of Contents for POWERSTEAMER PROHEAT PLUS 16981 Series



















Reviews: