background image

 

 

Created 11.08.2014: 

Approved 11.08.2014: 

 Bodo Kiesewalter 

 

 

Guide line to check and repair the safety equipment of the 

Robusta Plus Sliding Gate ver. 1.0 

 

 

 

 

 

Contents 

1. Technical data of the Robusta Plus Sliding gate ............................................................................. 1 

2. Checklist in case of failure Drive unit C720 / 721 ........................................................................... 2 

3. Checklist in case of failure Drive unit C746 / 844 ........................................................................... 3 

4. Manual for to check the safety devices of the sliding gates guiding post / lock post .................... 4 

5. AERF System (Wireless Band) ......................................................................................................... 9 

6. Installation of resistive safety strip at the front of the wing of Robusta Plus sliding gate ........... 11 

6.1 Table of required resistive safety strip (SAP code) according the height of the gate ................ 11 

6.2 Procedure to connect resistance safety strip to the AERF system ............................................. 12 

Electrical drawing safety strips E780 ................................................................................................ 14 

Electrical drawing photocells E780 ................................................................................................... 15 

 

 

 

 

 

1. Technical data of the Robusta Plus Sliding gate 

 

 

Type of FAAC unit:______________   Dimension:______________  Construction year:_______ 

 

 

Summary of Contents for Robusta Plus
















Reviews: