BendPak XPR-9FS Installation And Operation Manual Download | Manualshive

Page: 1 / 56

background image

INSTALLATION AND OPERATION MANUAL

SHIPPING DAMAGE CLAIMS

When this equipment is shipped, title passes to the
purchaser upon receipt from the carrier. Consequently,
claims for the material damaged in shipment must be
made by the purchaser against the transportation
company at the time shipment is received.

BE SAFE

Your new lift was designed and built with safety in mind.
However, your overall safety can be increased by proper
training and thoughtful operation on the part of the operator.
DO NOT operate or repair this equipment without reading this
manual and the important safety instructions shown inside.

1645 Lemonwood Dr.

Santa Paula, CA. 93060, USA

Toll Free: 1-800-253-2363

Tel: 1-805-933-9970

Fax: 1-805-933-9160

wwwbendpak.com

Keep this operation manual near the

machine at all times. Make sure that

ALL USERS read this manual.

9,000 POUND CAPACITY
SURFACE MOUNTED
TWO-POST LIFTS

MODELS:
XPR-9FS
XPR-9FXS

VERSION A

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO
INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT
YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF
THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO
OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.

REV A 07-16-10

p/n 5900166

XPR-9FSX

1
2
3
...
»

Summary of Contents for XPR-9FS

























































Reviews:

No comments

Related manuals for XPR-9FS

Brand: Magmaweld Pages: 8

Brand: Magmate Pages: 20

Brand: Magliner Pages: 20

Brand: Parweld Pages: 20

Hardon mini R1271C

Brand: Caen RFID Pages: 39

NeverFreeze SX-0810-24

Brand: ThermoSoft Pages: 5

Liftkar SAL Uni

Brand: SANO Pages: 24

Brand: M-system Pages: 7

Brand: Longevity Pages: 25

Brand: Danfoss Pages: 8

Brand: Telwin Pages: 196

Brand: Balluff Pages: 7

Brand: ICP DAS USA Pages: 8

WECS II 512 DMX/02

Brand: Oase Pages: 87

Ampac MAN3053-1

Brand: Halma Pages: 6

Digital Car Puller 5000

Brand: Telwin Pages: 104

Fusion splicer 232103

Brand: Televes Pages: 24

Brand: jbc Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands