background image

INSTALLATION AND OPERATION MANUAL

SHIPPING DAMAGE CLAIMS

When this equipment is shipped, title passes to the 
purchaser upon receipt from the carrier.
Consequently, claims for the material damaged in
shipment must be made by the purchaser against the 
transportation company at the time shipment is received.

BE SAFE

Your new lift was designed and built with safety in 
mind. However, your overall safety can be increased by 
proper training and thoughtful operation on the part of the 
operator. DO NOT operate or repair this 
equipment without reading this manual and 
the  important safety instructions shown inside.

1645 Lemonwood Dr.

Santa Paula, CA. 93060, USA

Toll Free 1-800-253-2363

Tel: 1-805-933-9970

Fax: 1-805-933-9160

www.bendpak.com

Keep this operation manual near the 

machine at all times. Make sure that 

ALL USERS  read this manual.

COMMERCIAL GRADE 
ROLLING BRIDGE JACKS

MODELS:
RJ-45; RJ-45S; RJ-6; 
RJ-7: RJ-9; RJ-12;
RJ-15; RJ-18; RJ-25. 

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO 
INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT 
YOU FULLY UNDERSTAND AND  COMPREHEND THE FULL CONTENTS OF 
THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO 
OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.

REV D  05-16-10

p/n 5900034

RJ-6 shown

Summary of Contents for RJ-12





























Reviews: