![background image](http://html1.mh-extra.com/html/sealey/re9720/re9720_instructions_1225313001.webp)
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION & CONTENTS
1. SAFETY INSTRUCTIONS
1.1
GENERAL SAFETY
p
WARNING!
Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
3
Only fully trained and qualified persons should use this equipment. Familiarise yourself with the application and limitations, as well as the
specific potential hazards, of the repair kit.
p
WARNING!
No part of this unit or any accessory relating to the repair kit is designed for lifting loads. It is intended only as a
pushing device and must be used as such, with care.
p
WARNING!
Disconnect the repair kit from the hydraulic pump before servicing or performing any maintenance on the unit.
3
Maintain repair kit in good order. Replace/repair with genuine parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
3
Use qualified person to lubricate and maintain the hydraulic pump.
DO NOT
use brake fluid to top up hydraulic unit. Use Sealey hydraulic oil
only.
3
Keep the repair kit clean for best and safest performance.
p
WARNING!
Ensure you know how much load you are pushing. Never exceed the maximum pushing capacity.
3
Use only with the supplied Sealey hydraulic pump and accessories. Other equipment may damage unit and will invalidate your warranty.
3
The kit accessories may be used with other popular makes of kit.
3
Ensure there is positive engagement of repair kit accessories with the vehicle body before pushing.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
If working on an off centre load, pump with care. If you feel undue resistance, stop and re-adjust the set-up.
p
WARNING!
Keep your hands, body and clothing away from the repair kit and accessories when in use. Take any necessary precautions to
protect your personal safety and that of others whilst using the repair kit.
3
Ensure the hydraulic hose is not bent or kinked.
3
Keep non-essential persons away from the operating area. Be aware of the locations of other persons assisting you.
3
When releasing tension from the load be sure to undo the hydraulic valve
VERY
slowly.
7
DO NOT
operate the repair kit if any parts are damaged or missing as this may cause failure and/or personal injury.
p
WARNING! DO NOT
use repair kit as a lifting device of any type.
DO NOT
use for any purpose other than for which it is designed.
7
DO NOT
over extend the ram as the plunger may be forced out of the cylinder.
7
DO NOT
heat accessories as this may weaken them.
7
DO NOT
modify accessories for use with this kit.
3
When not in use, place dust cap on end of hydraulic hose and store the kit, in the case, in a safe, dry, childproof location.
INSTRUCTIONS FOR:-
Hydraulic Body
Repair Kit 20tonne Snap Type
Model No:
RE9720
RE9720 Issue No: 1 - 22/11/12
Original Language Version
© Jack Sealey Limited 2012
Kit features heavy duty snap-together tubing and cast steel snap together-attachments. Compatible with most other leading snap-together
equipment. Supplied with 20tonne hand-lever operated pump, hose, hydraulic ram, pressed steel storage case with swivel castors and puller
strap for ease of transporting through workshop.
Castors
1
2
4
8
9
5
6
7
12
11
10
3
Item Part No
Description
1
RE9720.20-01
Pump assembly
2
RE9720.20-01
Ram assembly
3 RE9720.20-P10 Hose
4
610/A2
Snap tubing (600mm)
5
610/A3
Snap tubing (450mm)
6
610/A4
Snap tubing (300mm)
7
610/A5
Snap tubing (150mm)
8 610/A6
Adaptor
9
RE9720.20-05
Flat base
10
610/7
Serrated saddle
11
610/11
Wedge head
12
RE9720.20-03
Pressed steel case
For spare parts of pump, ram and hose etc. see
Parts Support.
3. ASSEMBLY
3.1
Unscrew the end plugs from the hose and hydraulic ram. Retain end caps for use when storing the kit.
3.2
Screw the hose into the hydraulic ram. Ensure the hose is secure but
DO NOT
overtighten.
3.3
Fit the pump handle to the pump unit -
DO NOT
overtighten.
To provide maximum versatility a combination of pump accessories may be used.
3.4
To use the flat base plate (item 9) and snap tubing sections (items 4-7) with the hydraulic ram, see Fig. 3.
Fig.1
Fig.2
Close
Release