Installation and Technical Information
BEGA
Accessories
Please refer to the appropriate
accessory installation sheet for
further instruction when applicable.
In the interest of product improvement, BEGA reserves the right to make technical changes without notice.
BEGA
1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2017
Replacement Parts
Fig-1:
(5/16" - 18 x 10")
Bollard - trapezoidal with step baffle
99 558
Tools Required:
6mm hex key
1/2” nut driver
Phillips medium screwdriver
Protection Class:
IP65
Weight:
22 lbs.
Dimensions
A:
9-7/8 ”
B:
43-3/8 ”
C:
5-1/2 ”
Relamping/Maintenance
No relamping required.
99 558
12/1/2017
Page 1 of 2
Description
Faceplate
Driver (120-277V)
LED Module (3000K)
LED Module (4000K)
Part No
FP8534
75985-01
LED-0313/930
LED-0313/940
Anchorage
79 817
Notice to Installer for 99 558:
1. Fixture may be damaged if connected to conduit systems that contain water - Article 300-5G of
the National Electric Code requires that “Conduits or raceways through which moisture may contact
energized live parts shall be sealed or plugged at either or both ends.”
2. 79 817 anchorage kit (included) must be installed in concrete pad/foundation.
3. It is recommended that when installing in planting areas the bollard base be slightly elevated to
avoid prolonged submerging during heavy rains.
4. Wet location listing does not imply suitability for exposure to standing water for long periods of time.
5. Integral LED driver supplied with luminaire.
6. LEDs are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation.
79 817 anchorage installation:
1. Provide means to bring supply wiring to the bollard in accordance with local code. The template has
a 2-3/8” conduit hole for conduit entry.
2. Assemble anchorage kit. Unscrew the (3) hex bolts from the female couplers. Remove each hex
bolt and washer. Align each anchor bolt with the hole in the template. Attach each anchor bolt to the
template by replacing the washer and hex bolt and tightening.
3. Determine the finished grade for the application. Use leveling hardware to adjust template to
desired finished height after pouring.
4. Install anchorage kit using either method:
A. Attach template to forming or cross bracing using the (2) nail holes
provided in the template. Level template properly. Pour concrete.
B. Insert anchorage assembly into poured concrete. Concrete must be
vibrated to ensure proper anchorage setting. Level template properly.
99 558 installation:
1. Remove (3) hex bolts and washers, once anchorage is set.
2. Remove template, making sure that there is a smooth, flat surface to mount the base.
3. Loosen the 5mm set screw at the base of the fixture. Turn the base plate and remove from bollard.
4. Align base plate holes with anchorage holes.
5. Bolt the base plate to the anchorage kit using the (3) hex bolts and washers.
6. Make supply wiring connections to wire leads from driver inside the fixture
MAIN VOLTAGE SUPPLY WIRE TO BLACK DRIVER WIRE;
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE DRIVER WIRE;
GREEN GROUND WIRE TO GREE N DRIVER WIRE.
Dimming (if applicable):
DIMMING CONTROL WIRE (+) TO POSITIVE DRIVER DIM CONTROL WIRE
DIMMING CONTROL WIRE (-) TO NEGATIVE DRIVER DIM CONTROL WIRE
7. Place the bollard over the base plate so that the (3) notches in the base plate align with the top.
Lock fixture into place by turning bollard 1/4” turn.
8. Secure the bollard by tightening the 6mm set screw at the base.
Lamp:
17.9W LED
