Barrett 1101 Installation And Operating Instructions Manual Download | Manualshive

Page: 1 / 15

background image

#0-313A-SBA (6/01)
Page 1 of 14 pages
BARRETT CENTRIFUGALS INC.
1-800-228-6442

Manufacturers of Reliable Centrifuges for the Metalworking Industry

INSTALLATION AND OPERATING INSTRUCTIONS FOR STANDARD BARRETT MODEL

401 & 1101 COMBINATION EXTRACTORS

Includes instructions for optional heaters and 45-gallon capture tank

Serial No. 4010263-E Motor No. 6R3467

This machine is designed to spin machining fluids (cutting oils, coolants, etc.) from industrial
sludge. Prior to using it on any other application you should contact Barrett Centrifugals Inc.
to determine if the machine can be used successfully and safely.

THIS EQUIPMENT MUST BE INSTALLED, WIRED, OPERATED AND SERVICED BY
QUALIFIED PERSONS ONLY. READ, UNDERSTAND AND COMPLY WITH THESE
INSTALLATION, OPERATING AND SAFETY INSTRUCTIONS BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.

SAFETY IS ESSENTIAL

To insure safe machine operation proper installation and thorough operator training are
required. Read and observe all instructions and specific precautions included in this manual
and most importantly, think before you act and be careful.

1
2
3
...
»

Summary of Contents for 1101
















Reviews:

No comments

Related manuals for 1101

Brand: Mytee Pages: 16

Brand: HAKO Pages: 52

Brand: Teka Pages: 28

Brand: Jema Autolifte Pages: 15

AlphaBlower EX 100

Brand: RadonTec Pages: 36

Brand: Powr-Flite Pages: 12

Brand: Thulos Pages: 14

Brand: Truvox Pages: 19

RootsScrub B4550C

Brand: ROOTS Pages: 22

LindWash 30 Class A

Brand: Lindhaus Pages: 20

Brand: Kränzle Pages: 92

Brand: Grizzly Pages: 36

Brand: Cleanfix Pages: 12

Brand: Cleanfix Pages: 11

Brand: Cleanfix Pages: 28

Brand: Crescent Pages: 47

Brand: Nilfisk-Advance Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands