ATI Technologies QC-50 Series Manual Download

Page: 1 / 35

Manual, Tool Changer, QC‑50
Document #9620‑20‑B‑50 Tool Changer‑04

Pinnacle Park • 1031 Goodworth Drive • Apex, NC 27539 • Tel: 919.772.0115 • Fax: 919.772.8259 •

www.ati‑ia.com

• Email:

info@ati‑ia.com

B-1

Table of Contents

B. Base Tool Changer ..................................................................................................................B-3

QC-50 Series—Robotic Tool Changer ........................................................................................B-3

1. Product Overview ..................................................................................................................B-3

1.1

Master Plate Assembly ............................................................................................................. B-4

1.2

Tool Plate Assembly .................................................................................................................. B-5

1.3

Optional Modules ...................................................................................................................... B-5

2. Installation .............................................................................................................................B-6

2.1

Master Interface ......................................................................................................................... B-7

2.2

Master Plate Installation ........................................................................................................... B-8

2.3

Master Plate Removal ............................................................................................................... B-8

2.4

Tool Interface ............................................................................................................................. B-9

2.5

Tool Plate Installation ............................................................................................................. B-10

2.6

Tool Plate Removal ................................................................................................................. B-10

2.7

Optional Module with J16 Pattern Installation .......................................................................B-11

2.8

Optional Module with J16 Pattern Removal ...........................................................................B-11

2.9

Optional K Series Module Installation ................................................................................... B-12

2.10 Optional K Series Module Removal ....................................................................................... B-12

2.11 Pneumatic Connections and Valve Requirements ............................................................... B-13

2.11.1 Valve Requirements and Connections for the Locking Mechanism ..............................B-13

2.12 Electrical Connections ............................................................................................................ B-14

2.12.1 PNP Type Lock and Unlock Sensors .............................................................................B-14

2.12.2 NPN Type Lock and Unlock Sensors ............................................................................B-14

3. Operation .............................................................................................................................B-15

3.1

Conditions for Coupling ......................................................................................................... B-16

3.2

Fail-Safe Operation ................................................................................................................. B-17

3.3

Conditions for Uncoupling ..................................................................................................... B-18

3.4 Tool Identification

.................................................................................................................... B-18

3.5

Tool Storage Considerations ................................................................................................. B-19

4. Maintenance .........................................................................................................................B-20

4.1

Preventive Maintenance ......................................................................................................... B-20

4.2

Cleaning and Lubrication of the Locking Mechanism and Alignment Pins ....................... B-21

4.3

Pin Block Inspection and Cleaning ....................................................................................... B-23

Summary of Contents for QC-50 Series




































Search results

Summary of Contents for QC-50 Series

Reviews:

Related manuals for QC-50 Series

Brands by name

Popular brands

ATI Technologies QC-50 Series, Manual

Search results

Summary of Contents for QC-50 Series

Reviews:

Related manuals for QC-50 Series

Brands by name

Popular brands