background image

 

 -  Do not store or use gasoline or other fl ammable 

vapors and liquids in the vicinity of this or any 
other appliance.

 -  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance. 
•  Do not touch any electrical switch; do not use 

any phone in your building. 

•  Leave the building immediately.
•  Immediately call your gas supplier from a neigh-

bor’s phone.  Follow the gas supplier’s instruc-
tions. 

•  If you cannot reach your gas supplier, call the 

fi re department.

 -  Installation and service must be performed by 

a qualifi ed installer, service agency or the gas 
supplier.

       

WARNING:

FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could 
result in serious injury, death, or property damage.

        AVERTISSEMENT:

RISQUED’INDENDIE OU D’EXPLOSION
Le non-respect Des avertissements de sécurité 
pourrait d’entraîner des blessures graves, la mort 
ou des dommages matériels.

 -   Ne pas entreposer ni utilizer d’essence ni d’autres 

vapeurs ou liquides infl ammables dans le voisinage 
de cet appareil ou de tout autre appareil.

 -   QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir 

des téléphones se trouvant dans le bâtiment où 
vous trouvez. 

•  Sortez immédiatement de bâtiment.
• Appelez immédiatement votre fournisseur de 

gaz depuis un voisin. Suivez les instructions du 
fournisseur. 

• Si vous ne pouvez rejoindre le fournisseur de gaz, 

appelez le service des incindies.

  -    L’installation et l’entretien doivent être assurés par 

un installateur ou un service d’entretien qualifi é 
ou par le fournisseur de gaz.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future 
reference.

Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour 
consultation ultérieure.

This appliance may be installed as an OEM installation in a manufactured home (USA only) or mobile home and 
must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction 
and Safety Standard, Title 24 CFR, Part 3280, in the United States, or the Standard for  Installation in Mobile 
Homes, CAN/CSA Z240 MH, in Canada. This appliance is only for use with the type(s) of gas indicated on the 
rating plate. A conversion kit is supplied with the appliance.

Cet appareil peut être installé comme du matériel d’origine dans une maison préfabriquée (É.-U. seulement) 
ou mobile et doit être installé selon les instruc! ons du fabricant et conformément à la norme Manufactured 
Home Construction and Safety Standard, Title 24 CFR, Part 3280 aux États-Unis ou à la norme CAN/CSA Z240 
Série MM, Maisons mobiles au Canada. Cet appareil doit être u! lisé uniquement avec les types de gaz indi-
qués sur la plaque signalé! que. Une trousse de conversion est fournie avec l’appareil.

Installation and Operation Instructions

Models

PFS

®

US

C

Report No. F13-094

Ce manuel est disponible en francais, simplement 
en faire la demande. Numéro de la pièce 900738-01.

P/N 900738-00   REV. B   04/2017

MHD35 Series Direct-Vent Gas Fireplaces

MHD35DMN

MHD35DMP

P900738-00

Summary of Contents for MHD35 Series









































































Reviews: