background image

SERENITY 2.5M

Assembly Manual

Kit Contents

‡

 - Fiberglass Fuselage Pod with Canopy

‡

 -  Tapered Carbon/Glass-composite Tail Boom

‡

 - Pre-sheeted and Shaped 4-segment Wing

‡

 - Pre-sheeted and Shaped V-tail halves w/hinged elevators

‡

 - Carbon Wing Tip Joiners 6 x 100mm (4)

‡

 - Wing Bolt M4 stainless (2)

‡

 - V-tail Mount Set (1)

‡

 - V-tail Mount Plate (1)

‡

 - Triangle Top V-tail Joiner (1)

‡

 - V-tail mounting screw M3  (2)

‡

 - Nylon retainers for the V-tail mounting screws (2)

‡

 - V-tail retaner -composite w/M3 nuts (1)

‡

 - V-tail Control Horns Set (2)

‡

 - Control Horns for the Ailerons and the Flaps (4)

‡

 - Pushrod wire for Aileron and Flap (2)

‡

 - Light weight Pushrod set for elevators (2)

‡

 - Fiberglass cloth.

‡

 - Glider Drawing

 

Recommended Tools and Supplies:

‡

 -

 Hobby Knife (blade #11)

‡

 -

 5 Minute Epoxy (#A0201).

      (use for joining the wing panels and tail)

‡

 -

 20 Minute Finishing Epoxy (#A0209)

     (use for fiberglassing the joints)

‡

 -

 CA adhesive (#A0101).

‡

 -

 Masking tape

‡

 -

 Pliers

‡

 -

 Drill

‡

 -

 Drill Bits: 2mm, 4mm, 6mm

‡

 -

 Soldering Iron

‡

 -

 1 meter ruler

‡

 -

 Flexible metal ruler (Approximately 200mm long will be

       easiest to use)

‡

 -

 Covering Trim to customize the color scheme.

‡

 -

 2 x 24” and 2 x 36”servo wire extensions

     (#H00X24 & H00X36)
     or 100 Inches of Servo Wire to make your
     own extensions

‡

 -

 Universal wing servo covers (#A0031)

‡

 -

 Clear lacquer (DEFT)

Check the Items Needed, Tools and
Supplies, and Contents sections.
Verify the contents of the kit and
your supplies before continuing.
If you have any other problems or
questions, please contact customer

service in the U.S.A. at:

Customer Service

1122 Ginger Ave.

Billings, MT 59105

 (406) 545-4118

Email:

[email protected]

Visit us at

w w w.arthobby.com

If this is your first model, please seek
the advice of other experienced
modelers prior to assembly and
flight. An internationally recog-
nized nonprofit sanctioning orga-
nization for modeling is the Acad-
emy of Model Aeronautics. They can
provide club, field, and liability in-
surance information. Contact them

for information at:

AMA

5151 East Memorial Drive

Muncie, IN 47302-9252

(800) 435-9262

Fax: (765) 289-4248

Internet:

www.modelaircraft.org

Serenity  v.11/2005

Summary of Contents for SERENITY 2.5M







Reviews: