background image

* Size rounded off to the nearest foot

BUILDING DIMENSIONS

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE
MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES
TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ
SAFETY INFORMATION PROVIDED IN THIS MANUAL
BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES
WHEN HANDLING METAL PARTS.

709521207

Model No.

HM10667

RMG106

      RMW106

      VH106-A

Owner's Manual & Assembly Instructions

       U1

                                                                       Exterior Dimensions             Interior Dimensions             Door

       *Approx.       Foundation        Storage Area           (Roof Edge to Roof Edge)              (Wall to Wall)               Opening
           Size               Size             Sq. Ft.  Cu. Ft.        Width      Depth      Height      Width     Depth    Height   Width  Height

         10' x 6'     121" x 68 3/4"           54        325         123 1/4"    71 1/4"     77 7/8"     118 1/4"       66"      76 5/8"   55 1/2"    65"

3,0m x 1,7m  307cm x 175cm        5,0m

2

     9,2m

3

          313cm       181cm       198cm       300cm      168cm     195cm      141cm   165cm

Summary of Contents for HM10667

































Reviews: