background image

Miller Manufacturing, Glencoe, MN 55336 USA  •  www.miller-mfg.com

Setup and Operation

SPECIFICATIONS

W250/DT250/BDT250: 250 watts, 120 VAC, 60 Hz 
W500/DT500: 500 watts, 120 VAC, 60 Hz

WARNING 

1. Have a qualified electrician install a properly 

grounded receptacle outlet, acceptable for 
outdoor use and protected from snow and 
rain, immediately adjacent to the location 
where the heater will be used.

2. Route the supply cord and locate the  

heater so as to be protected from damage  
by livestock.

3. Do not use extension cords.
4. Inspect cord before using.
5. Unplug heater at receptacle outlet when not 

in use or before removing from tank.

6. Store heater indoors after winter season.
7. Connect to properly grounded outlets only.
8. Heating element MUST be completely 

submerged while in use to prevent risk of fire 
hazard.

9. Do not tether unit. 
10. 

Connect only to a circuit that is protected 

by a Ground Fault Circuit Interrupter 
(GFCI).

 This is a sensitive device that cuts 

off the electricity if there is any leakage of 
current.  This device may be obtained from 
any electrician or hardware store.

IMPORTANT

This product is approved for use only with the 
LOCKNDRY® extension cord.  It is not approved 
for use with any other extension cords.  The 
plug on this product is specially designed 
to mate with the LOCKNDRY® cord to form 
a water-resistant seal.  See the LOCKNDRY® 
instructions at right.

OPERATION

Simply place the unit into the water that you 
wish to keep de-iced.  Connect the cord to a 
properly grounded, GFCI-protected receptacle 
while observing the cautions above. The unit 
will turn on when the water temperature 
approaches freezing conditions and will heat 
the water 10 to 20 degrees Fahrenheit before 
turning off.
Multiple thermostats within the unit monitor 
water temperature as well as guard against 
overtemp conditions. Please note: the unit 
will not turn on unless the water temperature 
is approaching freezing.  If you wish to test 
the unit, you must place it in a freezer for 15 
minutes to get it cold enough to turn on.

WARRANTY

This de-icer is warranted for a period of 1 
year from the date of purchase.  If you believe 
your de-icer is defective and still within the 
warranty period, return it to the factory or 
place of purchase for inspection and possible 
replacement. The warranty is voided if (1) 
the ground terminal on the plug has been 
removed, (2) excessive deposits have been 
allowed to accumulate on the heating element, 
or (3) there is evidence of general abuse such 
as animals chewing on the cord. This warranty 
does not cover incidental or consequential 
damage resulting from either a defect in parts, 
materials, or operation failure.  Some states 
do not allow the exclusion or limitation of the 
above damages so the above limitation may 
not apply to you.  No agent, employee, or 
representative of Miller Manufacturing has any 
authority to bind Miller Manufacturing to any 
affirmation, representation or warranty directed 
towards any products bearing the API name, 
except as stated herein. This warranty gives you 
specific legal rights--you may also have other 
rights which vary from state to state.

MAINTENANCE

Do not allow lime or other impurities in the 
water to build up on the heating element. The 
frequency of cleaning depends directly upon 
the composition of your water supply. The unit 
is coated for easy cleaning.  However, you may 
wish to use lime-removing cleaners that can be 
obtained at any farm or hardware store. Use a 
soft brush for cleaning.

INSTRUCTIONS FOR THE 

LOCKNDRY® CORDSET

- Plugs into any normal 3-prong outlet
- Mates with LOCKNDRY® plugs to form a  

water-resistant seal

- Keeps connection from separating during use
- Features a second, locking nut for a secure  

connection

INSTRUCTIONS

(1) Insert the plug 
into the receptacle 
just as you would a 
normal extension 
cord making sure 
the plug is fully 
inserted.

(2) Slide the large 
nut forward 
to engage the 
threads on the 
plug.

(3) Rotate the nut 
to tighten the 
plug against the 
receptacle. 

(4) Slide the 
second, thinner, 
red nut forward 
to engage the 
threads.

(5) Rotate the red 
nut snugly against 
the larger nut.

UTILITY/BUCKET/BIRD BATH/WATERER DE-ICERS

Item # W250, # W500, # DT250, # DT500 and # BDT250

304152

Reviews: