Analog Devices ADcmXL1021-1 User Manual Download

Page: 1 / 13

EVAL-ADCM / EVAL-ADCM-1 User Guide

Date: Jan 18, 2020

ADcmXL Evaluation Wiki link:

https://wiki.analog.com/resources/eval/user-guides/inertial-mems/imu/adcmxl-pc-eval

Contents

EVAL-ADCM / EVAL-ADCM-1 User Guide

............................................................................................ 1

Orderable Part Numbers

....................................................................................................................... 1

Minimum PC System Requirements

................................................................................................... 2

Minimum Required Hardware

............................................................................................................... 2

EVAL-ADCM Hardware Setup

............................................................................................................. 3

Software Installation

............................................................................................................................... 5

Troubleshooting

.................................................................................................................................. 6

Verifying the USB Connection

.......................................................................................................... 6

Application Functional Overview and User Guide

............................................................................. 6

Devices

................................................................................................................................................ 6

.................................................................................................................................. 7

Alarms

.................................................................................................................................................. 8

Data Capture

..................................................................................................................................... 10

View

.................................................................................................................................................... 11

Comm

................................................................................................................................................. 11

Help

.................................................................................................................................................... 11

About

.................................................................................................................................................. 11

Mode Selection (AFFT, MFFT, MTC and RT)

............................................................................. 11

Orderable Part Numbers

•

The EVAL-ADCM is an orderable kit that includes ADcmXL3021 module and all necessary

boards to interface with a PC.

•

The EVAL-ADCM-1 is an orderable kit that includes ADcmXL1021-1 module and all

necessary boards to interface with a PC.

Summary of Contents for ADcmXL1021-1














Search results

Summary of Contents for ADcmXL1021-1

Reviews:

Related manuals for ADcmXL1021-1

Brands by name

Popular brands

Analog Devices ADcmXL1021-1, User Manual

Search results

Summary of Contents for ADcmXL1021-1

Reviews:

Related manuals for ADcmXL1021-1

Brands by name

Popular brands