Analog Devices AD911 Series User Manual Download | Manualshive

Page: 1 / 12

background image

Evaluation Board User Guide

UG-073

One

Technology

Way

•

P.O.

Box

9106

•

Norwood,

MA

02062-9106,

U.S.A.

•

Tel:

781.329.4700

•

Fax:

781.461.3113

•

www.analog.com

Evaluating the AD9114/AD9115/AD9116/AD9117 and

AD9714/AD9715/AD9716/AD9717 DACs

FEATURES

Full featured evaluation board for the

AD9114/AD9115/AD9116/AD9117 (AD911x) and
AD9714/AD9715/AD9716/AD9717 (AD971x)

Includes options to evaluate

DAC only
DAC and ADL5375 quadrature modulator
DAC and op amp performance

USB interface for configuration
Internal or external power supply regulation
On-board or external clock distribution
Data pattern generator and SPI software interfaces

EQUIPMENT NEEDED

USB 2.0 port, recommended (USB 1.1 compatible)
HSC-DAC-DPG-BZ (DPG2) board
AD9114/AD9115/AD9116/AD9117 or

AD9714/AD9715/AD9716/AD9717 evaluation board

Spectrum analyzer

SOFTWARE NEEDED

DAC software suite
AD9717 software update

RELATED DOCUMENTS

Data sheets are available for both the AD911x and AD971x
products for product-specific details, including register defin-
itions. The DPG2 user guide is also available for assistance with
vector generation and loading.

GENERAL DESCRIPTION

This user guide describes the AD911x and AD971x evaluation
boards, which provide all of the support circuitry required to
operate the AD911x and AD971x in their various modes and
configurations. The application software used to interface with
the devices is also described.

The AD9114/AD9115/AD9116/AD9117 and AD9714/AD9715/
AD9716/AD9717 data sheets, available at

should be consulted when using the evaluation board. The
AD971x/AD911x Rev. A evaluation board operates together
with the Data Pattern Generator 2 (DPG2) and the DAC
software suite, including the AD971x/AD911x update.

The CD-ROM provided with the evaluation board includes
the installation program for all necessary software. The install
program can also be downloaded. Both methods install the
DPGDownloader program for loading vectors as well as the
AD971x/AD911x update necessary for SPI communication.

All documents and software tools are available online at

www.analog.com/dpg

.

Please see the last page for an important warning and disclaimers.

Rev. 0 | Page 1 of 1

2

1
2
3
...
»

Summary of Contents for AD911 Series













Reviews:

No comments

Related manuals for AD911 Series

Brand: Danbit Pages: 70

JW-A880GM-FUSION

Brand: J&W Pages: 38

Brand: ST Pages: 77

Brand: AMPTRON Pages: 16

Brand: Icop Pages: 40

Brand: Analog Devices Pages: 9

Brand: Commell Pages: 53

Brand: Texas Instruments Pages: 20

Brand: Biostar Pages: 115

LCMXO3L-DSI-EVN

Brand: Lattice Pages: 2

Brand: Texas Instruments Pages: 35

Brand: Aaeon Pages: 108

Brand: Commell Pages: 60

Brand: Mercury Pages: 57

Brand: Texas Instruments Pages: 24

Brand: ASROCK Pages: 2

Brand: NXP Semiconductors Pages: 35

Brand: NXP Semiconductors Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands