![background image](http://html1.mh-extra.com/html/amt/2008-dodge-challenger-srt8/2008-dodge-challenger-srt8_manual_2936348001.webp)
READ THIS BEFORE YOU BEGIN
VISIT THE
“WORKBENCH”
AT www.round2models.com FOR COMPLETE DETAILS ON PAINTING THE 2008 DODGE CHALLENGER SRT8!
• Carefully study and understand the entire instruction sheet before removing any parts from the trees
• Compare the parts in the box to the instruction sheet to be sure all parts are present and accounted for
• Use clippers or hobby knife to remove parts from the trees - DO NOT twist or bend parts off the trees
• Sand or trim away excess and flash and parting lines from parts before assembling
• As you proceed "TEST FIT" the parts to insure proper location and alignment before cementing
• Sub-assemblies should be painted before other parts are attached
• Use only paints and cements which are specifically formulated for styrene
• Use cement sparingly or a sloppy job may result
FOLLOW ASSEMBLY SEQUENCE AS SHOWN AND READ ALL NOTES VERY CAREFULLY
Completed Assembly
Apply Decal
3
Assembly Sequence
RECOMMENDED PAINT COLORS
SYMBOLS
Aluminum
Gloss Black
Amber
Silver
Semi-Gloss Black
White
Flat Black
Red
Part Number
49
DECAL
1/25 SCALE
A615-200
PAINTING TIPS:
Use a solution of mild soap and water to wash parts thoroughly, to remove any dirt or oily
residue. Dry parts with a soft towel, then allow them to fully air-dry. Keep your hands and working area clean
and dry when assembling your model kit.
Apply a coat of "primer" prior to painting. Glue joints may then be filled and sanded. Use only filler putty
designed for plastic. Test filler on some scrap plastic before applying to your model kit. A tack rag may be
used to remove any lint or sanding dust before painting. Paints should be applied evenly in several thin layers
rather than one heavy coat. Each layer should be allowed to thoroughly dry before the next is applied. Each
coat may be "wet sanded" using slightly damp minimum #1200 sandpaper. Be careful not to remove molded
details while sanding. Use frosted tape to mask areas you do not want painted. Remove tape when paint is dry
to the touch. Paint lightest colors first. Use a fine brush to touch up edges.
DECALS:
See back of decal sheet for application
instructions. Many of the very small decals in this kit have
been included in duplicate to serve as backups, should any
get lost or otherwise compromised during application.
REFER TO BOX ART PHOTOS FOR PAINTING DETAILS
1. WHEELS & TIRES
Carefully trim center cores from tire along the four joining points.
Repeat for remaining 3 tires.
NOTE: To make the tires easier to stretch, run them under very warm water for
30-60 seconds.
BE CAREFUL NOT TO BURN YOUR HANDS.
24
SRT WHEEL (Chrome)
Repeat for remaining 3
wheels and tires.
(Vinyl Tire with
core removed)
(Vinyl Tire)
Stretch tire over wheel making sure it is fully seated.
DECALS MUST BE APPLIED TO CERTAIN PARTS PRIOR TO
ASSEMBLY. SEE SECTION 3 FOR FULL DETAILS.
6. FINAL ASSEMBLY
(Completed Chassis)
(Completed Interior)
Dodge and HEMI® are trademarks of Chrysler LLC. Dodge Challenger SRT8 and its trade dress are used under license by Round 2, LLC.
©
Chrysler LLC 2009. AMT is a registered trademark of Learning Curve Brands, Inc.
used under license to Round 2, LLC. ©2009 Learning Curve Brands, Inc. All rights reserved. ©2009 Round 2, LLC, South Bend, IN 46628 USA. Product and packaging designed in the USA. Made in China. All rights reserved.
28
WINDOW UNIT
11
REAR SPOILER
11
FUEL FILLER
CAP
16
LEFT SIDE VIEW MIRROR
9
SRT CHIN SPOILER
(Completed Rear Fascia)
5
(Completed Front Fascia)
5
(Completed Hood)
5
17
RIGHT SIDE VIEW
MIRROR
(To pegs inside
roof)
(Align screw posts
to ribbed holes in top side
of completed chassis)
NOTE: Mount body to chassis using supplied screws.
Refer to Section 2/CHASSIS for additional locating information.
BODY TO CHASSIS
INSTALL 4 SCREWS
(Shown in place)
(Repeat for other side)
(To holes
inside body)
Apply decal of your choice to
recessed area of rear bumper.
DECAL
DECAL
DECAL
DECAL
Using box photos for reference, install hood
stripe decal of your choice. Align the Dodge
shield on decal over the despression in front
fascia and wrap front edge of stripes under.
Align Dodge shield on decal
over despression here.
OPTION
SIMULATED CARBON FIBER (Factory)
RED WITH PINSTRIPE (Custom)