TMMW25 Instruction Insert Sheet-FRONT
INSERT SIZE: 7" x 8.5" (2 per 8.5" x 14" sheet)
COLORS: Use Pantone Color Chip(s) for Color Matching
THIS PRINT IS FOR REFERENCE ONLY AND IS
NOT INTENDED FOR COLOR MATCHING
BLACK
DIE LINE
TMMW25
Mechanical Wall Switch Timer Instructions
• 24 hour on/off timer. Up to 24 ON and 24 OFF settings in a 24 hour period.
• 1 pin = 30 minutes
• Easy to install in a standard 2-1/2 inch vertically installed junction box
replacing a standard single pole single throw wall switch.
INSTALLATION
1. Turn off power to the branch circuit at the circuit breaker.
2. Remove the existing switch.
3. Using the wire nuts provided connect the wires of the timer and wall
box as instructed below. (See wiring schematic)
3.1 Connect the HOT/Live of the branch circuit (Black) to the black
wire from the timer.
3.2 Connect the Neutral wires of the branch circuit and load from
the box (white) to the white wire from the timer.
3.3 Connect the HOT/Live wire of the load to the red wire from the
timer.
3.4 Ground wire is not required for this timer because the cover is
non conductive.
Note:
Be sure all wire nut connections are secure.
4. Tuck the wires into the wall box leaving room for the timer
5. Using the screws provided, mount the timer to the wall box being
careful not to crush any wires.
Timer lock and switch insert
The TMMW25 is provided with 2 inserts to allow the timer to be locked
in timer mode or used with “ON/OFF/TIMER” switch.
The switch cover allows the switch to be moved to select the “TIMER“,
“OFF” or “ON” modes. The TIMER LOCK insert locks the switch in the
“TIMER” mode and will not allow the switch to be changed without
replacing the insert.
Select the desired insert and place it in the cover plate before attaching
to the installed timer.
Timer operation:
Setting ON / OFF Periods
This timer can be programmed with up to 24 on and 24 off settings in
a twenty-four hour time period. There are 2 pins (30 Minutes each)
associated with each hour in the day. Using your finger, a pen, or a
screwdriver, pull up (OFF) all pins corresponding to the times you want
the timer to turn power off to the load. For desired “ON” times, make
sure the pins are pushed down. The pins are typically set to the “ON”
position when you open the package.
Setting time of day
Turn outer dial clockwise until triangular pointer is lined up with the
present time of day. Be sure switch is set to “TIMER”.
Caution: Turning dial counter clockwise will damage the unit causing it
to stop working.
Selecting Mode: ON / OFF / TIMER
If you want the timer to run the ON / OFF programs as you set them in
previous section, you must select “TIMER” mode on the switch below
the dial. Programmed ON / OFF times can be interrupted by using the
“ON /OFF/ TIMER“ switch located just below the dial. After placing the
switch in the OFF or ON Position the controlled device will stay OFF or
ON untiI the switch is manually changed. If the “Timer Lock” is
installed, the switch is forced into the TIMER mode and cannot be
changed until the lock is removed. This feature is best utilized in public
locations where you don’t want someone overriding the timer settings
and turning a device on/off for extended periods of time.
Caution:
For indoor Use only
Do not use with any appliance that exceeds the capacity of the
timer.
Fan heaters and heaters with exposed elements should not be
connected to timers.
1 Year Limited Warranty
AmerTac warrants to the original
purchaser that this product will be
free from defects in materials and
workmanship for a period of 1 year
from the date of purchase. Additional
details are available at
www.amertac.com.
PROP. 65
WARNING:
This product contains
chemicals known to the State of
California to cause cancer, birth
defects or other reproductive harm.
Questions, ¿Preguntas?, Questions? 201-661-9945
©2013 AmerTac™
Saddle River Executive Centre
One Route 17 South, Saddle River, NJ 07458
www.amertac.com
Made in China/Fabriqué en Chine/ Hecho en China
I13-0004-A
Black
Red
Black
White
White
Light
Timer
120 AC
Power In
White
White
Timer is non metal construction so no ground
wire is required for timer housing
Typical wiring schematic
Wallbox
Boîtier
Caja de pared
Timer
Minuterie
Temporizador
Front Cover
Couvercle avant
Cubierta frontal
Switch cover (optional)
Couvercle de l’interrupteur
(optionnel)
Cubierta del interruptor
(opcional)
Use one or the other
Utiliser l’un ou l’autre
Utilice uno de los dos
Timer Lock
(optional)
Dispositif de
verrouillage
de la minuterie
(optionnel)
Bloqueo del
temporizador
(opcional)
