background image

508096-01

Issue 2037

Page 1 of 34

SERVICE MANUAL

A80UH1E / 80G1UHE

 

(P) 508096-01

*P508096-01*

Table of Contents

Technical Specifications - A80UH1E

 ...........................2

Technical Specifications - 80G1UHE

 ...........................5

Parts Arrangement

.......................................................8

Unit Components

 .........................................................9

Placement & Installation

 ............................................22

Start-Up

 .....................................................................22

Heating System Service Checks

 ...............................22

Typical Operating Characteristics

 ..............................26

Maintenance

 ..............................................................27

Wiring Diagram

 ..........................................................30

Troubleshooting: Heating Sequence of Operation

 ....31

Troubleshooting: Heating Sequence of Operation 

(Continued)

 ................................................................32

Troubleshooting: Cooling Sequence of Operation

 .....33

Troubleshooting: Continuous Fan / Accessories 

Sequence of Operation

..............................................34

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in manuals, be alert to 

the potential for personal injury or death.

Electric shock hazard. 
Can cause injury or death. Before attempting 

to  perform  any  service  or  maintenance, 

turn  the  electrical  power  to  unit  OFF  at 

disconnect  switch(es).  Unit  may  have 

multiple power supplies.

 WARNING

As with any mechanical equipment, contact with sharp 

sheet  metal  edges  can  result  in  personal  injury. Take 

care  while  handling  this  equipment  and  wear  gloves 

and protective clothing.

 CAUTION

Improper  installation,  adjustment,  alteration,  service 

or maintenance can cause property damage, personal 

injury  or  loss  of  life.  Installation  and  service  must  be 

performed by a licensed professional HVAC installer (or 

equivalent), service agency or the gas supplier.

 WARNING

Summary of Contents for 80G1UHE



































Reviews: