1
2
3
4
5
6
7
8
MARK DOOR
BORE 3 HOLES
INSTALL LATCH AND STRIKE
REMOVE INSIDE TRIM
ADJUST FOR
DOOR
THICKNESS
ENGAGE LOCK WITH LATCH
SECURE LOCK TO DOOR
INSTALL KNOB
Recommended template instructions
must be followed to assure proper
functioning. (See attached template).
Mark centers for latch hole, side hole
and rose insert points on both sides of
door.
A. Bore side hole from both
sides of door.
B. Bore latch hole.
Use strike locating tool
or other pointed object
to locate position for
hole in jamb.
C. Bore jamb.
NOTE:
A minimum
³⁄₄
”
deep hole must be
bored in frame behind
opening in strike for
proper function of latch bolt.
Outline latch face and strike as illustrated
and chisel out to proper depth.
Install latch.
Be sure beveled
side of latch
bolt is facing
the door frame.
If dust box is
to be used,
clear area
with wood
chisel.
Depress knob catch to remove knob.
Remove rose by unscrewing collar
If Cylinder knob, see reverse side.
Hold lock against edge of door. Adjust
outer rose collar so door center mark on
lock housing is in center of door.
Wrench can be used to adjust lock for door
thickness by holding tip of wrench against
rose insert and turning rose collar until
desired arrow on wrench lines up with arrow
on lock case.
ALTERNATE
METHOD
Centerline of
door and lock
Door Edge
12172 WRENCH
Both latch prongs engage housing.
Housing
Retractor
engages
latch tail.
Replace inside rose and collar
and using spanner wrench
turn collar clockwise and
tighten firmly.
Place knob on spindle, slide to knob
catch, depress knob catch and push
knob until catch engages slot in knob.
If cylinder knob, see reverse side.
TEMPLA
TE FOR S AND X SERIES
RECOMMENDED
TEMPLA
TE INSTRUCTIONS MUST
BE FOLLOWED
TO
ASSURE PROPER FUNCTIONING.
DIST
ANCE
FROM EDGE
OF DOOR
(BACKSET)
¹⁄₈
” DIA
(3.2 mm)
2 HOLES
¹⁄₈
” DEEP
BOTH SIDES OF DOOR
3
³⁄₄
"
(95 mm)
2
³⁄₈
"
(60 mm)
FOLD ALONG EDGE OF DOOR
SECOND
BORE LA
TCH HOLE
PARALLEL
T
O
SIDES.
⁷⁄₈
” (22mm) FOR 2
³⁄₈
” BACKSET
1” (25mm) FOR 2
³⁄₄
”
OR LONGER BACKSET
CENTER
FOR 1
³⁄₈
”
(35 mm)
DOORS
CENTER
FOR 1
³⁄₄
”
(44 mm)
DOORS
Remove template from instructions.
FIRST
BORE 2
¹⁄₈
” (54 mm) HOLE
AT
CORRECT
BACKSET
AND
¹⁄₈
” (3.2 mm)
CLEARANCE HOLES FOR ROSE INSER
T POINTS
TEMPLA
TE FOR S AND X SERIES
RECO
MMENDED
TEMPLA
TE INST
RUCTIO
NS MUST
BE FO
LLOWED
TO ASSURE PROPER F
UNCTIO
NING.
DIST
ANCE
FROM EDGE
OF
DOOR
(BACKSET)
¹⁄₈
” DIA
(3.2mm)
2 HO
LES
¹⁄₈
” DEEP
BOTH SI
DES OF DOOR
3
³⁄₄
"
(95 mm)
2
³⁄₈
"
(60 mm)
FIRST
BORE 2
¹⁄₈
” (54 mm) HOLE
AT CORRECT
BACKSET
AND
¹⁄₈
” (3.2
mm) CL
EAR
ANCE HOLE
S FOR ROSE
INSER
T PO
INTS
FO
LD
ALONG
EDGE
OF
DO
OR
SECO
ND
BORE LA
TCH HO
LE
PARALLEL
TO
SIDES.
⁷⁄₈
” (22mm) FOR 2
³⁄₈
” BACKSET
1” (25mm) FOR 2
³⁄₄
”
OR LONGER BACKSET
CENT
ER
FO
R 1
³⁄₈
”
(35mm)
DO
ORS
CENT
ER
FO
R 1
³⁄₄
”
(44mm)
DO
ORS
Remove temp
late from instructions.
B
A
C
