!
PLEASE READ
BEFORE USE!
ENSURE POWER SUPPLY IS OFF WHEN HANDLING ANY ELECTRICAL EQUIPMENT.
•
Read and Understand the detailed Installation Instructions before installing the LED T8 Tube Light.
•
LED T8 Tube Lights are designed to work with Electronic/Magnetic Ballasts (Check the Ballast
Compatibility List) or AC Direct Wire. Works with Single-end (either side) and/or
Double-end Power Input. Risk of Fire or Electric Shock. Read and Understand all Installation
Instructions before installing LED T8 Tube Lights. Use in Dry or Damp locations only.
Do not use where directly exposed to water or weather. Non-submergible (not water tight).
•
Disable all Power to the Fixture before Inspection, Installation, or Removal. Failure to do so will
create a Hazardous and Fatal Working Environment.
•
Do Not Make or Alter any Open Holes in an Enclosure of Wiring or Electrical Components during
Installation.
•
Do Not Open – No User Serviceable Parts inside.
Safety
•
Do not cover the ground contact.
•
Do not cover the luminaire, hang or fasten anything from it.
•
Do not operate if any visible damage can be seen to the product.
•
Do not operate if any water ingress has occurred.
•
Do not operate if any smoke, steam or crackling noises can be heard from the luminaire.
•
Do not operate if any signs of overheating are recognised.
•
Avoid installation in any areas where there is a risk of strong mechanical loads.
•
Do not place any material over the lens or LED diode/chip.
•
Do not insert objects into the luminaire.
•
Do not clean using any solvent based abrasive or aggressive product.
•
Do not pull any cables connected to the product.
•
Do not direct the luminaire into a persons eyes, as this unit may have an intense light output,
which if incorrectly used may cause eye damage.
•
Light engines/LED’S and other light sources may heat up, please take care when handling the
products.
•
The manufacturer will not be deemed liable or held responsible for any damages caused by faults
or manufacturing defects that may be present in any of its products or the misuse or incorrect
installation of this device. Please refer to our trouble shooting guide for further information.
•
The manufacturer will not be held liable for any death(s) or injuries caused by misuse or poor
installation or any unreported faults of this product version or versions thereof.
•
LED’s are sensitive to electrostatic discharge. Do not touch the surface of the LED module.
•
Do not connect to a temporary electricity supply, this may damage the electronics.
•
Light fittings with an integrated emergency option are with a separate installation and wiring
leaflet. Please refer to this manual for further details. If the manual is unavailable please contact
an ALL LED representative for assistance.
•
REPLACE DAMAGED PRODUCT IMMEDIATELY.
•
Keep away from children.
Returns & Faulty Items
•
If any problem is encountered during or after installation, please call ALL LED technical department to get the
problem resolved ASAP.
•
Please do not just return the item to the outlet you purchased it from, as you are only entitled to a replacement
or refund after the unit has undergone testing and the unit has been confirmed as having a manufacturing
defect/fault. Your statuatory rights are not affected.
•
The manufacturer will not be deemed liable or held responsible for any damages caused by faults or
manufacturing defects that may be present in any of its products or the misuse or incorrect installation of this
device.
•
All installations must be carried out in accordance with this installation guide and user manual.
•
All goods are supplied under the terms and conditions of ALL LED LTD, a copy of which may be obtained upon
written request.
This product supplied with a limited 5 year guarantee, subject to terms and conditions.
The manufacturer will not be deemed liable or held responsible for any damages caused
by faults or manufacturing defects that may be present in any of its products or the misuse
or incorrect installation of this device Your statuatory rights are not affected.
SAFETY WARNING
INSTALLATION GUIDE
AL-T8LED12AB Range
Environmental Protection
Waste electrical products
should not be disposed of
with household waste. Please
recycle where facilities exist.
Check with your Local Au-
thority or retailer for recycling
advice
ALL-LED USA LLC
12035 34th St N, Suite 2
St Petersburg
FL 33716 USA
Website: www.all-ledusa.com
Email: [email protected]
a. Risk of Fire or Electric Shock. LED Retrofit Kit Installation requires knowledge of Luminaires
Electrical Systems. If not Qualified, DO NOT attempt Installation. Contact a Qualified Electrician.
b. Risk of Fire or Electric Shock. Install this Kit only in the Luminaires that have the construction
features and dimensions shown in the photographs and/or drawings and where the Input Rating
of the Retrofit Kit does not exceed the Input Rating of the Luminaire.
c. DO NOT make or alter any open holes in an enclosure of Wiring or Electrical Components during
Kit Installation
d. To prevent Wiring Damage or Abrasion, DO NOT Expose Wiring to edges of Sheet Metal or other
Sharp Objects.
e Installers should not Disconnect existing Wires from Lampholder Terminals to make new
Connections at Lampholder Terminals. Instead Installers should Cut existing Lampholder Leads
away from the Lampholder and make new Electrical Connections to Lampholder Lead Wires by
employing applicable Connectors.
f. For a Linear Tubular LED Lamp Conversion, there shall be text or a Diagram showing how the
supply Connections were made to the Lampholders so the correct Connections will be made to
the Lamp when the Lamp is Installed or Replaced.
g. This Retrofit Kit is accepted as a component of a Luminaire where the suitability of the
combination shall be determined by Authorities having JURISDICTION.
Note
: If the Tube is installed as Type B, the Luminaire, once modified as a Retrofit Fixture,
will no longer operate Fluorescent Lamps. Not Suitable for Use with Dimmer.
