background image

1

ALI-QVR40xxH_SQ  

180305

Item

Description

1

VIDEO IN 

BNC connectors for camera video channels in. Number of channels is dependent on the model of the DVR. 

2

VIDEO OUT

CVBS

3

AUDIO IN

RCA connector for audio in cable. 

4

ON / OFF switch

Switch for powering the DVR on and off

5

USB

Use for a USB mouse or USB memory device such as a flash drive or DVD burner. A USB port is also located on the front panel.

6

HDMI

Connector HDMI monitor cable. 

7

VGA

Connector VGA monitor cable. 

8

AUDIO OUT

RCA connector for audio out cable. 

9

LAN

RJ-45 connector for Ethernet drop cable.

10

RS-485 terminations

Connector for RS-485 devices. Connect the D+ and D- terminals to T+ and T- of PTZ receiver respectively.

11

12 Vdc

Plug for 12 Vdc power adapter (provided).

12

Alarm terminations

See 

Alarm terminations

 below. 

13

GND terminal

Ground terminal post. 

Alarm terminations 

Item

Description

RS-485 (D+, D-) 

D+ and D- pins connect to R+ and R- pins of PTZ receiver respectively. 

For cascading devices, the first DVR’s D+, D- pin should be connected with the D+, D- pin of the next DVR. 

ALARM IN 

Alarm inputs (ALI-QVR4008H: 1 .. 8, ALI-QVR4016H: 1 .. 16). Alarm input is tied to ground through the alarm sensor. See “Step 3. Connect 

alarm devices to the DVR” on page 2. 

ALARM OUT  

(1-G through 4-G)

Alarm outputs 1 - 4 with ground terminations. See “Step 3. Connect alarm devices to the DVR” on page 2. 

Mouse control

A standard 3-button (left / right / scroll-wheel) USB mouse can also be used with this DVR. To use a USB mouse: 

1. 

Plug the USB mouse into the either the front panel or back panel USB connector of the DVR.

2. 

The mouse will be automatically detected. If the mouse is not detected, the mouse may not be compatible with the DVR. Please refer 
to the recommended device list from your provider.

This guide provides instructions to initially setup the ALI-QVR4000H series digital video recorder (DVR) for AHD, HD-TVI, analog and IP 
cameras. The ALI-QVR4008H DVR supports up to 8 analog cameras plus 2 IP cameras (10 total). The ALI-QVR4016H DVR supports up to 
16 analog cameras plus 2 IP cameras (18 total). For information about using your DVR and its extensive capabilities, refer to the 

ALIBI 

Embedded Network Video Recorder Firmware V3.4.x User Manual

 provided at 

www.alibisecurity.com/resources

For more information

, refer to these documents - available from your equipment vendor: 

• 

ALIBI™ Tools Utility Installation and User Manual

• 

ALIBI™ Witness Smartphone App - Quick Start Guide

DVR Front Panel

USB Interface

Power LED

Status TX / RX

ALI-QVR4008H, ALI-QVR4016H front panel

Item

Usage

Power LED

Indicator turns green when DVR is powered up. 

Status

STATUS indicator lights in red when HDD is reading / writing.

TX / RX

LED indicator blinks green when network connection is functioning properly.

USB Interface

This port can be used for a USB mouse or USB flash memory devices.

DVR Back panels

1

2

3

4

13

12

11

10

9

8

7

6

5

ALI-QVR4008H backpanel

1

2

3

4

13

11

12

10

9

8

7

6

5

ALI-QVR4016H backpanel

ALI-QVR4000H Series 8/16-Channel AHD, HD-TVI, Analog and IP Camera Recorder Quick Setup Guide

Summary of Contents for ALI-QVR4008H Series

Page 1: ...USB mouse can also be used with this DVR To use a USB mouse 1 Plug the USB mouse into the either the front panel or back panel USB connector of the DVR 2 The mouse will be automatically detected If the mouse is not detected the mouse may not be compatible with the DVR Please refer to the recommended device list from your provider This guide provides instructions to initially setup the ALI QVR4000H...

Page 2: ...you are using for an AC load alarm then remove it Save the jumper for use later if needed 4 Reinstall the DVR top cover Using the mouse Action Effect Left click Single click Live view Select channel and show the quick set menu Menu Select and enter Double click Live view Switch between single screen and multi screen Click and drag PTZ control pan tilt and zoom Tamper proof privacy mask and motion ...

Page 3: ...Depending on the configuration of the network these settings may change To improve remote access to the recorder Observint recommends that you configure the DVR with fixed network settings To easily change the DHCP acquired network settings to fixed network settings un check the EnableDHCP option in the network setup menu and then click Apply DC load alarm output circuits DC loads must operate wit...

Page 4: ...ons W D H 15 0 12 6 1 9 in 380 320 48 mm Weight without HDD 2 kg 4 4 lb Step 8 Access the Menu system After the initial setup of your QVR using the Wizard the Menus interface enables you to refine your configuration settings and expand the functionality of the system To use most menus the user must log into the NVR system either locally or remotely with administrative privileges To open the Menu s...

Reviews: