• Use only the supplied battery.
• Remove any headset attachment (earbud excluded)
before battery replacement.
• If the headset will not be used for a long time,
remove the battery to prevent possible leakage.
• To purchase a replacement battery pack, contact
your Alcatel home & business phones partner. Use
only battery pack recommended by Alcatel home &
business phones.
You can register Alcatel IP70 onto the following
phones : Alcatel Temporis IP300 and Alcatel
Temporis IP700G. Both phones support one
headset only.
Register the headset with the telephone base
before use. After charged, the light on headset
flashes in red and blue slowly and alternately.
• Headset charger
• Cordless headset
with medium-sized
earbud attached
Parts checklist
Headset overview
1 – VOL+/VOL-
• Push to right or left to adjust the ringer volume
while in idle mode, or the listening volume while on
a call.
2 – MUTE/FLASH
• Press to mute the ringer in the earpiece when
there is an incoming call.
• Press to mute the microphone during a call.
• Press and hold for two seconds to answer an
incoming call when you receive a call waiting
alert during a call.
3 –
• Press to make, answer or end a call.
4 – Microphone
5 – Battery pack
• Open to replace the battery pack.
6 – Earpiece
Charger overview
1 – Magnetic charging mount
• Place the headset here for charging.
2 – Power cord slot
3 – Power jack
Light and alert tones overview
Light:
light status
Red
• On when the headset is charging in the
headset charger.
• Flashes every 10 seconds to indicate
the battery is low when the headset is
not in the headset charger.
• Flashes three times to indicate the
headset is powering off.
Blue
• On when a fully charged and registered
headset is in the headset charger.
• Flashes three times to indicate the
headset is powering on.
• Flashes twice every three seconds
when the headset is in use.
• Flashes four times every four seconds
when there is an incoming call.
• Flashes every 10 seconds when a fully
charged and registered headset in idle
mode is out of the headset charger.
Red
and
blue
• Flashes slowly when the headset is not
registered.
• Flashes quickly when the headset is
trying to register to a telephone base.
Off
• No battery is installed or out of battery.
• The headset is powered off.
Alert tones:
One short beep
Headset key tone.
One short beep
every 30 seconds
Muted headset microphone
alert tone.
Two beeps
• Error alert tone.
• The ringer volume is at its
lowest setting.
• The listening volume is at
its highest or lowest setting.
• Any key is pressed while
the headset is out of range
Two low beeps
Call waiting alert tone.
Two rapid beeps
every 20 seconds
Low battery warning.
Three rising beeps A conference call starts.
Three rapid beeps
every 20 seconds
• The headset is out of range.
• The headset is not yet
registered.
Ring tone
• Incoming call alert tone.
• Ring back tone.
Three rapid beeps
The headset is powering on
or off.
Install the battery
NOTE
• The battery is permanently attached to the battery
compartment cover (known as the battery pack). Do
not try to separate them from each other.
Install the battery as shown below.
NOTES
Connect and charge the battery
NOTES
• Use only the supplied adaptor.
• Charge the battery provided with or identified for
use with this product only in accordance with the
instructions and limitations specified in this manual.
Connect the charger
Charge the battery
The light turns on when the headset is
charging.
NOTES
• For best performance, keep the headset in the
charger when not in use.
• The battery is fully charged after three hours of
continuous charging.
• When fully charged, the headset battery provides
approximately 12 hours of talk time or 5 days of
standby time.
Before use
Add and register a headset
NOTE
• Charge the new headset without interruption for
at least 30 minutes before registering it to the
telephone base.
To register a headset:
1. Remove the headset from the charger.
2. Press Menu at the telephone base when idle.
3. Press
q
to highlight User Settings, and then
press SELECT.
4. Press
q
to highlight DECT headset, and
then press SELECT.
5. With Register highlighted, press SELECT on
the telephone base.
6. Place the headset back to the charger. The
light flashes quickly in red and blue.
The light turns red when the headset is
registered but not fully charged, or turns blue
when it is registered and fully charged.
To verify the registration, press the button on the
headset and check for a dial tone. If the
registration fails, the light on the headset flashes
slowly in red and blue.
To reset the headset, remove it from the headset
charger and repeat the registration process
again.
Deregister a headset
To replace a headset or register the headset to
another telephone base, you must deregister
all devices, and then register each device
individually.
To deregister all devices:
1. Press Menu at the telephone base when idle.
2. Press
q
to highlight User Settings, and then
press SELECT.
3. Press
q
to highlight DECT headset, and
then press SELECT.
4. Press
q
to highlight Deregister, and then
press
SELECT
.
The light flashes slowly in red and blue when
the deregistration process is successful.
Position the headset
Earbud
There are three sizes of earbuds provided. The
medium-sized earbud is already attached to the
headset.
To remove the earbud from the headset
earpiece:
• Hold both sides of the earbud. Twist and
pull the earbud until it separates from the
earpiece.
To attach the earbud to the headset
earpiece:
1. Choose an appropriate earbud.
2. Position the earbud on the earpiece.
3. Press the earbud down on the earpiece until
it clicks into place. Move the earbud around
so that the protruding bump on the earbud is
pointing towards your mouth when placed in
your ear.
Over the ear hook
There are two sizes of ear hooks. You can
choose the suitable ear hook to attach to the
headset.
To adjust the headset to wear on the left or
right ear:
To attach the ear hook to the headset:
1. Remove any headset attachment (earbud
excluded) currently connected to the headset.
2. Insert the earpiece into the ear hook ring.
3. Press the edge of the ear hook ring towards
the earpiece until it clicks into place.
4. Hook the headset onto the desired ear.
Adjust the angle of the headset until the
microphone is pointing towards your mouth.
To remove the ear hook from the headset:
• Hold the headset with one hand. Twist and
pull the ear hook with your other hand until it
separates from the earpiece.
Over the head band
To attach the head band to the headset:
1. Remove any headset attachment (earbud
excluded) currently connected to the headset.
2. Insert the earpiece into the loop of the ear pad.
3. Push the earpiece towards the loop of the
ear pad until it clicks into place.
4. Adjust the head band to fit your head. Adjust
and rotate the angle of the headset until the
microphone is pointing towards your mouth.
To remove the head band from the
headset:
• Hold the headset with one hand and the ear
pad with your other hand. Twist and pull the
headset until it separates from the loop of the
ear pad.
User’s manual
• Battery pack
(with battery
compartment cover
attached)
• Headset charger
power adapter
• Earbud x5
• Over the ear hook
x2
• Over the head band • Behind the neck
band
• User’s manual
1
2
3
4
5
6
1
2
3
• To wear on the
left ear
• To wear on the
right ear
Your headset package contains the following
items. Save your sales receipt and original
USER'S GUIDE
PLEASE READ THIS USER'S GUIDE BEFORE USING THE HEADSET
Alcatel IP70H
