Agora Models Bismarck 08 Build Instructions Download

Page: 1 / 54

Pack 08 | Build Instructions

Your 1:200 scale model of the legendary battleship Bismarck is packed with

intricate details which precisely replicate every aspect of this state-of-the-

art warship. Each piece has been created using premium quality materials to

bring maximum enjoyment during your complete build.

In your eighth model pack, you will assemble:

North America Edition by Agora Models

STAGE 81: A HULL SECTION AND CATWALKS

STAGE 82: MORE DETAILS FOR THE HANGARS AND

MAIN DECK

STAGE 83: FITTING THE NEXT KEEL SECTION

STAGE 84: THE MAIN CIRCUIT BOARD

STAGE 85: A SECTION OF HULL AND DECK DETAILS

STAGE 86: TWO TWIN 10.5CM GUNS AND RAILINGS

STAGE 87: HEAVY AA GUNS AND BRIDGE WINGS

STAGE 88: THE NEXT SECTION OF THE HULL

STAGE 89: MOTOR FOR THE AFT FIRE

CONTROL POST

STAGE 90: A HULL SECTION AND MAGNETS

STAGE 91: THE AFT FIRE CONTROL POST

STAGE 92: THE TURBINE ROOM

WARNING

Some parts are assembled using magnets. These magnets can cause serious injury if they

are swallowed. Keep away from children. If you suspect a magnet has been swallowed,

seek medical help straight away.

Summary of Contents for Bismarck 08























































Search results

Summary of Contents for Bismarck 08

Reviews:

Related manuals for Bismarck 08

Brands by name

Popular brands

Agora Models Bismarck 08, Build Instructions

Search results

Summary of Contents for Bismarck 08

Reviews:

Related manuals for Bismarck 08

Brands by name

Popular brands