View the expanded manual:
http://aeotec.com/support
WallMote Quad.
Aeotec WallMote Quad is an intelligent Z-Wave remote controller that
mounted on a wall. It has 4 touch buttons that you can easily control
the Z-Wave devices in your home network via touching, long pressing
or sliding the button areas.
Its surface has a RGB LED to indicate the button actions also
accompanied by touch beep and vibration.
The WallMote Quad is also a security Z-Wave device and supports
Over The Air (OTA) feature for the products firmware upgrade.
Familiarize yourself with your WallMote Quad.
Quick start.
Advanced.
1.
2.
Installing your WallMote Quad.
Adding your WallMote Quad to your Z-Wave network.
Attach your WallMote Quad to its Back Mounting plate.
Send a wake up notification.
Removing your WallMote Quad from a Z-Wave network.
Security or Non-security feature of your WallMote Quad in Z-wave
network.
Advanced Parameter Configurations.
1.
2.
3.
4.
Let your Z-Wave primary controller/gateway enter into pairing/
inclusion mode.
Take your WallMote Quad near to your primary controller.
Press the Action Button once on your WallMote Quad, the LED will
blink with green color.
If your WallMote Quad has been successfully added to your Z-Wave
network, its green LED will be solid for 2 seconds and then off. If
the adding was unsuccessful and the red LED will be solid for 2
seconds and then off, repeat the above steps.
With your WallMote Quad added to the Z-Wave network. It’s now
time to insert the main unit into the corresponding Back Mount plate.
Put the main unit in the top-left direction on the Back Mounting, and
then push the WallMote Quad into the Back Mounting Plate, the
WallMote Quad will be attracted by the magnets on the Back Mount
plate, as the figure below shows.
With your WallMote Quad now working as a part of your smart home,
you’ll be able to configure it from your home control software or phone
application. Please refer to your software’s user guide for precise
instructions on configuring the WallMote Quad to your needs.
With your mounting plates prepared to hold each component of your
WallMote Quad, it’s time to add it to your Z-Wave network.
In order to send your WallMote Quad new configuration commands
from your Z-Wave controller or gateway, it will need to be woken up.
Remove your WallMote Quad unit from its Back Mounting Plate, press
and hold the Action Button for 3 seconds(the buzzer chirp once and
the orange LED will be ON) on the back of the WallMote Quad unit
and then release it. This will trigger and send a wake up notification
command to your controller/gateway, then your WallMote Quad will
wake up for 10 minutes and the orange LED will fast blink while it is
awake (if the WallMote Quad does not receive the Wake Up No More
Info from the primary Controller).
Your WallMote Quad can be removed from your Z-Wave network at
any time. You'll need to use your Z-Wave network's main controller/
gateway. To do this, please refer to the part of their respective
manuals that tell you how to remove devices from your network.
1.
2.
3.
4.
Put your primary controller into device removal mode.
Unlock your WallMote Quad from the Back Mount plate and take
the WallMote Quad unit near to your primary controller.
Press the Action Button on your WallMote Quad.
If your WallMote Quad is successfully removed from the Z-Wave
network, the LED will become a colourful gradient for a few
seconds and then turn off. If the removing was unsuccessful, the
red LED will be solid for 2 seconds and then turn off, repeat the
above steps.
Not all gateways will allow you to further configure your Z-Wave
devices, but in the case that your gateway does allow it, the WallMote
Quad has some available parameter configurations that will allow you
to configure it further to your liking.
Touch beep
This will enable or disable the sound effects when you press or touch
the sensing area. By default, this is enabled.
Parameter 1 [1 byte]
0: Disable
1: Enable
Including WallMote Quad as a non-secure device:
If you want your WallMote Quad as a non-security device in your
Z-wave network, you just need to press the Action Button once on
WallMote Quad when you use a controller/gateway to add/include it.
The green LED will be on for 2 seconds and then the orange LED will
fast blink for 10 minutes (if the WallMote Quad does not receive the
Wake Up No More Info command from primary Controller) to indicate
the inclusion is successful.
Selecting a place or wall in your home to affix your WallMote Quad’s
Back Mount plate.
Using the Double-sided tap, wipe the two surfaces clean of any oil
or dust with a damp towel. When the surface has completely dried,
peel one side of the tape back and attach it to the corresponding
section on the rear side of the Back Mounting Plate.
Advanced functions.
WallMote Quad
1
2
3
4
5
IMPORTANT!
This product has been fully tested and certified to work
with Z-Wave by the Z-Wave Alliance. It is crafted using
Z-Wave Plus, the latest device version of Z-Wave.
As such, if the product does not work with your
gateway, please be sure to check with your gateway
manufacturer that they have integrated this device with
their gateway for full operation.
1.
2.
3.
4.
WallMote Quad
Back-Mount plate
Double-Sided tape
Micro USB cable
①
®
②
③
④
RGB LED
Button 1
Button 3
Button 2
Button 4
Mangent
Mangent
Micro USB port
Action Button
Main unit (Front)
Main unit (Back)
Back-Mount plate
Mangent
Including WallMote Quad as a secure device:
In order to take full advantage of all functionality the WallMote Quad,
you may want your WallMote Quad is a security device that uses
secure/encrypted message to communicate in Z-wave network, so a
security enabled controller/gateway is needed for the WallMote Quad
to be used as a security device. You need to press the WallMote
Quad’s Action Button 2 times within 1 second when your security
controller/gateway starts the network inclusion. The blue LED will
be on for 2 seconds and then the orange LED will fast blink for 10
minutes (if the WallMote Quad does not receive the Wake Up No
More Info command from primary Controller) to indicate the inclusion
is successful.
