background image

ML-96 Installation Manual

Phase 7 / Non-Coin / Fire Suppression System

ADC Part No. 113362 - 25

AVERTISSEMENT:

RISQUE D’INCENDIE OU D’EXPLOSION

Le non-respect des avertissements de
sécurité pourrait entraîner des blessures
graves, la mort ou des dommages
matériels.

– N’entreposer pas et n’utilisez pas
d’essence ni d’autres vapeurs ou
liquides inflammables dans le voisinage
de cet appareil ou de tout autre appareil.

– QUE FAIRE SI VOUS SENTEZ UNE
ODEUR DE GAZ

Ne tentez pas d’allumer d’appareil.

Ne touchez à aucun interrupteur.  Ne
vous servez pas des téléphones se
trouvant dans le bâtiment où vous
vous trouvez.

Évacuez la pièce, le bâtiment ou la zone.

Appelez immédiatement votre
fournisseur de gaz depuis un voisin.
Suivez les instructions du fournisseur.

Si vous ne pouvez rejoindre le
fournisseur de gaz, appelez le service
des incendies.

– L’installation et l’entretien doivent être
assurés par un installateur ou un service
d’entretien qualifié ou par le fournisseur
de gaz.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly
could result in serious injury, death or
property damage.

– Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.

– WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliances.

Do not touch any electrical switch;
do not use any phone in your
building.

Clear the room, building or area of
all occupants.

Immediately call your gas supplier
from a neighbor’s phone.  Follow
the gas supplier’s instructions.

If you cannot reach your gas
supplier, call the fire department.

– Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.

!!!!!

!!!!!

American Dryer Corporation

88 Currant Road, Fall River MA 02720-4781 USA

Telephone: +1 (269) 923-3000 / Fax: +1 (508) 678-9447

e-mail: [email protected] / www.adclaundry.com

Summary of Contents for ML-96

























Reviews: