LR6000 INSTALLATION
DETAIL "A"
VERIFY CORRECT BACKSET
AND HORIZONTAL OR VERTICAL
MOUNTING BEFORE DRILLING.
THEN USE BACKSET TEMPLATE
THAT IS SUPPLIED.
INSTALLATION INSTRUCTIONS:
1. Prep door according to LR6000 Series latch template
2. Install latch using either #8 wood screws or 8-32 machine screws (Item 2).
3. Check (1) base assembly (Item 3) to ensure the cam is the position shown in Detail A (See above)
Place the base assembly on the push side of the door by inserting the cam shaft into the latch cam as
detailed above.
4. Check the other base assembly (Item 3) and ensure the cam is the position shown in Detail A
(See above). Place base assembly on the pull side of door by engaging the shaft into the latch cam as
detailed above. Fasten both base assemblies together with (4) 12-24 screws (Item 4) and (4) 12-24
hex nuts (Item 5). Test that cams rotate freely on both sides of the door after tightening the
screws.
5. Install the push handle assembly (Item 7) to the base assembly installed on push side of door using
(2) socket head cap screws (Item 8). Insert (1) stop pin (Item 9) through the push base assembly on
the the same side of the direction the push handle is pointing. Test push handle for proper
operation to be sure stop pin was installed in appropriate base assembly hole.
6. Repeat Step #5 on the pull side of the door for the pull handle assembly (Item 6). Insert (1)
stop pin (Item 9) through the pull base assembly on the opposite side of the direction the pull
handle assembly is pointing. Test pull handle for proper operaton to be sure stop pin was
installed in appropriate base assembly hole.
7. Place covers (Item 10) over handles and fasten each cover with (2) 8-32 screws (Item 11).
LATCH CAM
PARTS LIST
DESCRIPTION
QTY
ITEM
LATCH
1
1
2
2
BASE ASSEMBLY
2
3
12-24 X 2-1/2" PTHMS
4
4
4
5
HANDLE ASSEMBLY, PULL
1
6
HANDLE ASSEMBLY, PUSH
1
7
6-32 X 3/8" SHCS
4
8
STOP PIN
2
9
COVER
2
10
4
11
#8 X 3/4"FHWS OR 8-32 X 3/8"FHMS UC
12-24 HEX NUT
8-32 X 3/8" OVAL HEAD M.S.
10
11
11
3
1
8
8
11
11
10
8
8
7
5
9
2
3
CAM SHAFT
4
EDGE GUARD NOTE:
WHEN PREPPING THE DOOR FOR
THE BACKSET, DETERMINE IF THE
DOOR WILL RECEIVE AN EDGE
GUARD, IF SO, THE EDGE GUARD
SHOULD BE INSTALLED FIRST AND
THEN THE PREP FOR THE LATCH
BACKSET SHOULD BE MEASURED
FROM THE OUTSIDE EDGE OF THE
EDGE GUARD.
6
NOTE:
BEFORE MOUNTING BASE ASSEMBLIES,
CAM MUST BE ROTATED AS PER DRAWING
SHOWN IN DETAIL "A".
PATENT PENDING
ALL PREP MOUNTING HOLES
TO BE STRAIGHT & PARALLEL
TO ONE ANOTHER, THIS WILL
HELP PREVENT ANY BINDING
OF MECHANICAL PARTS.
NOTES
1. TRIM CAN BE MOUNTED UP, DOWN, HORIZONTALLY OR VERTICALLY.
2. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM.
**
HORIZONTAL
BACKSET
WITH 5" OR 7"
LEVERS
BACKSET
LEVERS
HORIZONTAL
DOWN
LEVERS
UP
LEVERS
PUSH
PULL
LEVERS
MIXED
PULL
PUSH
*
*
LOCK EDGE
POINTING
HINGE EDGE
POINTING
REVISED 11-05-18
PAGE 1 OF 3
LR6000-1-03.DWG
LR6000
Handle
Pointing
Direction
Handle
Pointing
Direction
2
12
COTTER PIN
12
12
9
1
13
7/64" ALLEN KEY
13
c
