background image


ABB Australia Pty Limited

For enquiries
ABB contact centre: 1800 60 20 20
E-mail: [email protected] 

www.stanilite.com.au

© Copyright 2020 ABB. All rights reserved. 

Troubleshooting guide

If you have installed and connected the fitting as per the instructions listed earlier and it does 
not function correctly, use the following table as a guide to fixing the problem. Look up the 
type of fault in the left column and check the possible causes from the right column.  

If the fitting still does not work after checking these possible causes, contact ABB customer 
service in Australia on 1800 60 20 20.

No. Fault

Possible causes

1

LED not lit; 

or

LED not flashing green

AC supply not connected; 

or

AC supply turned off

2

LED is flashing green but AC lamp does not come on 
when connected to mains

Switch active supply turned off; 

or

Missing loop from unswitched to switched active; 

or

Lamp damaged; 

or

Lamp not inserted properly

3

LED is flashing green but lamp does not come on when 
test switch is pressed

Lamp damaged or lamp not inserted properly; 

or

Battery pack not connected; 

or

Battery pack damaged; 

or

Test switch damaged

4

LED not red after the commissioning

Battery pack not connected; 

or

LED wire not properly inserted into the terminal 
block

5

Lamp is lit momentarily when test switch is pressed; 

or

 

When mains fail

Battery not fully charged (allow up to 24 hours); 

or

Battery pack damaged

6

LED is constant green

Fitting self checks fail - return to manufacturer

7

Fitting LED is not flashing yellow/orange under wink 
node command

Fitting is not receiving communication signal. Check 
data cable wiring path and cable connections. Refer 
to Nexus RF user guide.

Construction sites

Continuously switching off the mains power 
supply that is connected to emergency light 
fittings during the construction phase of an 
installation will cause these fittings to discharge 
and charge their batteries many times over a 
short period; this can shorten life of the battery. 
ABB does not recommend such practices and 
may not honour the warranty on batteries when 
they are subjected to such harsh operating 
conditions. Emergency light fittings are designed 
to be discharge tested once every 6 months as 
per AS/NZS 2293.2, subjecting the product to 
repeated discharge or charge cycles is regarded 
as an abuse of the fittings.

Testing precautions

Once the fitting is permanently connected to the 
mains supply, a commissioning discharge test as 
required in AS/NZS 2293.2 must be carried out. 
You will need to allow 24 hours for the battery to 
fully charge prior to conducting this test, 

presently (at the time of writing), the standard 

requires that fittings operate in emergency mode 
for a period not less than 2 hours for their 
commissioning test and for not less than 90 
minutes thereafter (it is required that 6 monthly 

discharge tests be carried out). You will need to 

keep the records for the commissioning test and 
enter them into the building emergency services 
logbook or via other recording methods as 
allowed by AS/NZS 2293.2.

 

I N S TA LL ATI O N  M A N UA L 

Stanilite®

Power pack T8

Nexus® RF

Thank you for choosing ABB product

Please read this document thoroughly before 
commencing installation and retain for future 
reference. Contact ABB customer service in 
Australia on 1800 60 20 20 if you need any 
assistance. The installation instructions were 
correct at the time of print. To reflect changes in 
technology and Australian standards; ABB 
reserves the right to amend the instructions 
without notice. Updated document can be found 
on the Stanilite website.

Safety warning

In Australia and New Zealand, only licensed 
electricians are permitted by law to work with 
240 volt electrical installations.
Do not attempt to install or connect this product 
unless you are a licensed electrician.
Turn off and isolate the electrical supply before 
connecting this fitting to the building wires.
Do not touch the terminals of the terminal block 
when the light fitting is energised.
The only user-serviceable part is the battery.
Do not attempt to service other parts of the 
fitting as this will void the warranty.
As the installer, it is your responsibility to ensure 
compliance with all relevant building and safety 

codes, (ie: AS/NZS 3000, AS/NZS 2293). Refer to 

the applicable standards for data and mains 
cabling installation procedures and 
requirements.

This document covers

What’s inside the box

Safety warning

Power pack T8 Nexus RF 

Installation instructions

Installation manual

Removal instructions

Warranty information

Testing precautions

Troubleshooting guide

Important to note:

•  This product is designed for indoor use only.

EMC warning

Power pack complies with EMC regulations. We 
advise that if you incorporate this pack into 

your product (batten/fitting) you must test the 
complete (product/fitting) for EMC compliance.

PL Lamp warning

For PL lamp application it is recommended that 
the power pack be used without a LDR. The fitting 
should be designated as a non-maintained fitting. 
The LDR is not designed to be affixed to a PL lamp. 
If AC lamp monitoring is required then the LDR 
must be mounted adjacent to the PL lamp. Please 
contact ABB customer service on 1800 60 20 20 
if you require more information. Specific PL lamp 
power packs are supplied without a LDR and are 
programmed as non-maintained.

Nexus RF (wireless system)

The Nexus RF power pack is a wireless RF system 
monitor conversion kit suitable for AC fluorescent 
luminaire to be converted to Nexus RF fluorescent 
emergency luminaire, they communicate via a 
proprietary RF network system. The power pack 
comes complete with Nexus RF MAC address 
label. Affix the Nexus RF MAC address label 
supplied with the power pack on to the retrofitted 
emergency fitting in a recognisable position for 
recording upon installation

Doc no. 29-01092_1

9

A

K

K

10

76

8

0

A

8

4

24 

Ju

n

20

20

Reviews: