ABB DS1 Installation And User Manual Download

Page: 1 / 32

Medium voltage products

DS1

Technical Guideline for Installation and User Manual

Safety

1. Introduction

1.1 Environmental protection program

1.2 Packing and transport

1.3 Checking on receipt

1.4 Storage

1.5 Handling

1.6 End of life of product

1.7 Disposal methods

2. Product Description

2.1 General features

2.2 Reference Standards

2.3 Fixed capacitor-switch

2.4 Main electrical characteristics

2.5 Apparatus operating instructions

2.6 Description of the capacitor-switch

closing and opening operations

2.7 DS1 Closing and Opening switching

behaviour

3. Description of the control and supply electrical

interface

3.1 Power Supply Characteristics

3.2 Description of the DS1 output

3.3 Electrical characteristics of the outputs

3.4 Description of DS1 inputs

3.5 Special INPUT - Only for commissioning

and maintenance

3.6 Electrical characteristics of the INPUT

3.7 Input Acceptance Logic

3.8 DS1 functional descriptions

4. DS1 Diagnostics

4.1 Base Module Diagnostics

4.2 Master Diagnostics

4.3 Synchronization Diagnostics

4.4 Diagnostics Table

5. Installation Guideline

5.1 General

5.2 Before installing the apparatus:

5.3 Installation requirements

5.4 Installation of fixed apparatus

5.5 Additional installation recommendations

5.6 Preliminary operations

6. Fixed Apparatus power circuit connections

6.1 General directions

6.2 Mounting the connections

6.3 Mounting procedures

6.4 Three-phase power line connections

6.5 Load connection

6.6 Synchronization sensor

6.7 Voltage Sensor Connections

6.8 Earthing

6.9 Auxiliary circuit connection

7. Commissioning

7.1 General procedures

7.2 Startup and maintenance features

7.3 Pressure Monitoring

7.4 Interface summary for Maintenance and

Commissioning

7.5 Commissioning - Test with no power,

no sync

8. Periodical inspections

8.1 General

8.2 Checking program

8.3 Measurement of air pressure inside poles

8.4 Dry Air filling

8.5 Dry air filling procedure

8.6 Measurement of resistance across closed

contacts of poles

8.7 Replacement due to System malfunctions

8.8 Spare parts and accessories

Annex A - Terminal Block for auxiliary control circuit 30
Annex B - External drawing for DS1 Integration

B.1 Overall dimensions

B.2 Internal connections

Provided

Northeast

Power

Systems,

Inc.

(NEPSI)

Summary of Contents for DS1

































Search results

Summary of Contents for DS1

Reviews:

Related manuals for DS1

Brands by name

Popular brands

ABB DS1, Installation And User Manual

Search results

Summary of Contents for DS1

Reviews:

Related manuals for DS1

Brands by name

Popular brands