A.O. Smith BTH 120-250(A) Installation & Operating Instructions Manual Download

Page: 1 / 32

A DIVISION OF A.O. SMITH CORPORATION

Mc BEE, SOUTH CAROLINA

PLACE THESE INSTRUCTIONS ADJACENT TO HEATER AND

NOTIFY OWNER TO KEEP FOR FUTURE REFERENCE.

PRINTED IN U.S.A. 1104

PART NO. 196145-001

CYCLONE XHE

Model BTH 120-250(A)

SERIES 970 AND 973

COMMERCIAL GAS WATER HEATER

GAS-FIRED POWER BURNER

FOR DOMESTIC HOT WATER

Thank you for buying this energy efficient water heater from
A.O. Smith Water Products Company. We appreciate your
confidence in our products.

CAUTION

TEXT IN BLACK BOLD TYPE OR UNDERLINED CONTAINS
INFORMATION RELATIVE TO YOUR SAFETY. PLEASE
READ THOROUGHLY BEFORE INSTALLING AND USING
THIS APPLIANCE.

• INSTALLATION • OPERATION • SERVICE • MAINTENANCE • LIMITED WARRANTY

WARNING: If the information in these

instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury or death.

– Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

– WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.
• Do not touch any electrical switch;

do not use any phone in your
building.

• Immediately call your gas supplier

from a neighbor's phone. Follow the
gas supplier's instructions.

• If you cannot reach your gas supplier,

call the fire department.

– Installation and service must be

performed by a qualified installer,
service agency or the gas supplier.

Summary of Contents for BTH 120-250(A)

































Search results

Summary of Contents for BTH 120-250(A)

Reviews:

Related manuals for BTH 120-250(A)

Brands by name

Popular brands

A.O. Smith BTH 120-250(A), Installation & Operating Instructions Manual

Search results

Summary of Contents for BTH 120-250(A)

Reviews:

Related manuals for BTH 120-250(A)

Brands by name

Popular brands