background image

1

DISC SANDER - PISTOL GRIP INSTRUCTION MANUAL

51 mm (2 in) 15,000 RPM
76 mm (3 in) 15,000 RPM

Important Safety Information

Please read, understand and follow all safety information contained in these instructions prior to the use of this tool.
Retain these instructions for future reference.

Intended Use

This pneumatic tool is intended for use in industrial locations, and used only by skilled, trained professionals in accordance with the instructions in this manual. This 
pneumatic tool is designed to be used with disc pads, and appropriate abrasive for sanding metals, wood, stone, plastics and other materials. It should only be used 
for such sanding applications and within its marked capacity and ratings. Only accessories specifically recommended by 3M should be used with this tool. Use in any 
other manner or with other accessories could lead to unsafe operating conditions.

Do not use disc pads that have a Max RPM less than the tool Max RPM rating.

Summary of device labels containing safety information

Marking

Description

W

 WARNING:

 

READ AND UNDERSTAND INSTRUCTION MANUAL BEFORE OPERATING TOOL.

 

W

 WARNING:

 

ALWAYS WEAR APPROVED EAR AND EYE PROTECTION.

W

 WARNING: 

REPETITIVE MOTION/EXTENDED EXPOSURE TO VIBRATION MAY HARM HANDS/ARMS.

W

 WARNING: 

ALWAYS OPERATE AT 90 PSIG/6.2 BAR MAX.

15,000 RPM

MAXIMUM ROTATIONAL SPEED

Hand/Wrist/Arm injury can occur with prolonged exposure to vibration

Explanation of Signal Word Consequences

 

WARNING:

Indicates a potentially hazardous situation which, if not avoided, may result in death or serious injury and/or property damage.

 

CAUTION:

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or property damage.

Original Instructions

Summary of Contents for 28547









Reviews: