![background image](http://html.mh-extra.com/html/2n/smartgate-umts/smartgate-umts_manual_439839001.webp)
Calls – DialThru Gateway
By default, 2N® SmartGate UMTS behaves
as a dial-thru gateway:
•
Calls are routed to UMTS/GSM from
the FXS interface.
•
Incoming UMTS/GSM calls ring at the
FXS interface.
•
When the FXO interface is ringing,
2N® SmartGate UMTS interconnects
FXO and FXS, thus enabling analogue
interfaces to communicate with each
other.
For more advanced call routing, you have
to program the routing tables. Some
distributors offer products with pre-
programmed routing for planned use:
•
2N® SmartGate UMTS can route calls
from the FXS interface to UMTS/GSM
and FXO according to the called
number, thus cutting the outgoing call
costs significantly. Be sure to program
the FXS routing table properly using
your
PC
and
the
PCManager
programming tool enclosed.
•
ME – Mobility Extension
is applied
whenever a call is coming (ringing) to
the FXO interface. With ME enabled, the
FXS and FXO lines are interconnected
and a call is set up to the defined
UMTS/GSM number. Hence, a FXO call
can be answered on the FXS interface
and/or UMTS/GSM network.
Calls – PBX Internal Line
Gateway
By programming a single parameter
assigned to the FXO routing table, you
can switch 2N® SmartGate UMTS into the
PBX internal line mode:
•
Calls from the FXO interface are routed
to the UMTS/GSM network.
•
To route incoming UMTS/GSM calls back
to the FXO interface, you also have to
set routing to FXO on the row for other
numbers in the GSM routing table. (To
make 2N® SmartGate UMTS process
calls from different UMTS/GSM callers,
complete the GSM routing table rows as
necessary.)
Configuration via USB
•
To enable configuration via a PC,
connect 2N® SmartGate UMTS to the
PC using a USB cable and install the
2N®SmartGate PCManager tool.
•
Thus you create a virtual serial port
(USB serial port, FTDI) for the
PCManager connection to the gateway
(launch CDM20814_Setup.exe to install
the drivers).
•
Select the virtual serial port number in
the PCManager setup.
•
Refer to the full User Manual version for
details.
Connection to Internet, SMS
•
2N® SmartGate UMTS can be used as a
modem for PC connection to GPRS,
EDGE, UMTS and HSDPA networks and
thus provide a high speed Internet
connection.
•
Install the modem drivers from the
Watcher_Generic_B2849.msi file before
connecting 2N® SmartGate to the PC.
•
When
2N® SmartGate
UMTS
is
connected and switched on, the AirCard
Watcher
program
is
launched
automatically, which helps you access
the Internet or send and receive SMS.
•
Be sure to set APN and other provider’s
settings if necessary in the connection
profile before connecting to the
Internet.
•
Refer to the full User Manual version for
details.
In the GSM network, data transfers are suspended during voice calls and
do not continue until the voice call has been finished, whereas in the
UMTS (3G) network, data and voice are transferred simultaneously.
EC Declaration of Conformity
2N TELEKOMUNIKACE a.s. hereby declares that the 2N® SmartGate UMTS product is in compliance with the
basic requirements and other relevant provisions of Directive 1999/5/EC. Refer to the CD-ROM enclosed or
www.2n.cz for the full wording of the Declaration of Conformity.
© 2011, 2N TELEKOMUNIKACE a.s. – Prague, LH 1713, v.1.00