ZyXEL Communications ZyWALL USG Series, Reference Manual

Page: 335 / 426

Chapter 52 System Remote Management
ZyWALL / USG (ZLD) CLI Reference Guide
335
52.8.3 SNMP Commands
The following table describes the commands available for SNMP. You must use the
configure
terminal
command to enter the configuration mode before you can use these commands.
vpnTunnelDisconnec
ted 1.3.6.1.4.1.890.1.
6.22.2.3 This trap is sent when an IPSec VPN tunnel is disconnected.
vpnTunnelName 1.3.6.1.4.1.890.1.
6.22.2.2.1.1 This trap is sent along with the vpnTunnelDisconnected trap. This
trap carries the disconnected tunnel’s IPSec SA name.
vpnIKEName 1.3.6.1.4.1.890.1.
6.22.2.2.1.2 This trap is sent along with the vpnTunnelDisconnected trap. This
trap carries the disconnected tunnel’s IKE SA name.
vpnTunnelSPI 1.3.6.1.4.1.890.1.
6.22.2.2.1.3 This trap is sent along with the vpnTunnelDisconnected trap. This
trap carries the security parameter index (SPI) of the
disconnected VPN tunnel.
Table 205
SNMP Traps (continued)
OBJECT LABEL OBJECT ID DESCRIPTION
Table 206
Command Summary: SNMP
COMMAND DESCRIPTION
[no] snmp-server
Allows SNMP access to the ZyWALL / USG. The
no
command
disables SNMP access to the ZyWALL / USG.
[no] snmp-server community community_string
{ro|rw}
Enters up to 64 characters to set the password for read-only
(ro) or read-write (rw) access. The
no
command resets the
password for read-only (
ro
) or read-write (
rw
) access to the
default.
[no] snmp-server contact description
Sets the contact information (of up to 60 characters) for the
person in charge of the ZyWALL / USG. The
no
command
removes the contact information for the person in charge of the
ZyWALL / USG.
[no] snmp-server enable {informs|traps}
Enables all SNMP notifications (informs or traps). The
no
command disables all SNMP notifications (informs or traps).
[no] snmp-server host { w.x.y.z|fqdn|ipv6
address } [ community_string ]
Sets the IPv4 or IPv6 address of the host that receives the
SNMP notifications. The
no
command removes the host that
receives the SNMP notifications.
[no] snmp-server location description
Sets the geographic location (of up to 60 characters) for the
ZyWALL / USG. The
no
command removes the geographic
location for the ZyWALL / USG.
[no] snmp-server port <1..65535>
Sets the SNMP service port number. The
no
command resets
the SNMP service port number to the factory default (
161
).
snmp-server rule { rule_number |append|insert
rule_number } access-group {ALL| address_object }
zone {ALL| zone_object } action {accept|deny}
Sets a service control rule for SNMP service.
address_object
: The name of the IP address (group) object.
You may use 1-31 alphanumeric characters, underscores(
_
), or
dashes (-), but the first character cannot be a number. This
value is case-sensitive.
zone_object
: The name of the zone. For some ZyWALL / USG
models, use up to 31 characters (a-zA-Z0-9_-). The name
cannot start with a number. This value is case-sensitive.
For other ZyWALL / USG models, use pre-defined zone names
like DMZ, LAN1, SSL VPN, IPSec VPN, OPT, and WAN.
snmp-server rule move rule_number to rule_number
Changes the index number of a service control rule.
no snmp-server rule rule_number
Deletes a service control rule for SNMP service.