Zycoo CooFone-D30 User Manual Download

Page: 66 / 79

DHCP option



AUTO PROVISION

Item

explanation

Auto Update Setting

Current Config Version

Show the current config file’s version. If the version of the configuration downloaded

is higher than the version of the running configurations, the auto provision would

upgrade, or stop here. If the endpoints confirm the configuration by Digest method,

the endpoints wouldn’t upgrade configuration unless the configuration in the server is

different with the running configuration.

Common Config Version

Show the common config file’s version. If the configuration downloaded and the

running configurations are the same, the auto provision would stop here. If the

endpoints confirm the configuration by Digest method, the endpoints wouldn’t

upgrade configuration unless the configuration in the server is different with the

running configuration.

CPE Serial Number

Show CPE Serial Number.

User

Specify FTP/HTTP/HTTPS server Username. System will use anonymous if username

keep blank.

Password

Specify FTP/HTTP/HTTPS server Password.

Config Encrypt Key

Input the Encrypt Key, if the configuration file is encrypted.

Common Config Encrypt

Key

Input the Common Encrypt Key, if the Common Configuration file is encrypted.

Save Autoprovision

Information

Save the username and password authentication message of http/https/ftp and input

ID message in the phone until the url in the server changes.

DHCP Option Setting

DHCP Option Setting

Specify DHCP Option. DHCP option supports DHCP custom option and DHCP option 66

and DHCP option 43 to obtain the parameters. You could choose one method among

them; the default is DHCP option disable.

Custom DHCP Option

A valid Custom DHCP Option is from 128 to 254. The Custom DHCP Option must be in

accordance with the one defined in the DHCP server.

Plug and Play

Enable PnP

Enable PnP by selecting it, than the phone will send SIP SUBSCRIBE messages to a

multicast address when it boots up. Any SIP server understanding that message will

reply with a SIP NOTIFY message containing the Auto Provisioning Server URL where

the phones can request their configuration.

PnP Server

Specify the PnP Server.

PnP Port

Specify the PnP Server.

PnP Transport

Specify the PnP Transfer protocol.

PnP Interval

Specify the Interval time, unit is hour.

Phone Flash

Server Address

Set FTP/TFTP/HTTP server IP address for auto update. The address can be IP address

or Domain name with subdirectory.

Config File Name

Set configuration file’s name which need to update. System will use MAC as config file

Summary of Contents for CooFone-D30














































































Search results

Summary of Contents for CooFone-D30

Reviews:

Related manuals for CooFone-D30

Brands by name

Popular brands

Zycoo CooFone-D30, User Manual

Search results

Summary of Contents for CooFone-D30

Reviews:

Related manuals for CooFone-D30

Brands by name

Popular brands