background image

 

 
Revision 1.5  

 

 

 

 

ZWEIMANN Technologies 

©

 

2016.11.19 

Do not route the power cord where it will be crushed, pinched, bent, exposed to heat, or damaged 
in any way. Pay particular attention to the power cord at the plug and where the cord exits the back 
of the unit.  
 
The power cord should be unplugged from the wall outlet during a lightning storm or if the unit is to 
be left unused for a long period of time.  
 
Immediately stop using the component and have it inspected and/or serviced by a qualified service 
agency if:  
 
• The power supply cord or plug has been damaged.  
• Objects have fallen or liquid has been spilled into the unit.  
• The unit has been exposed to rain.  
• The unit shows signs of improper operation.  
• The unit has been dropped or damaged in any way. 

 

 

FCC Notice - Declaration of Conformity Information 

 

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause 
harmful interference to radio communications.  
 
However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
 

WARNING: 

Only peripherals complying with the FCC class B limits may be attached to this 

equipment.  
 
Changes or modifications made to this equipment, not expressly approved by us or parties 
authorized by us could void the user’s authority to operate the equipment. This device complies 
with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device 
may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.  
 

Summary of Contents for DAC I2S DSD USB



















Reviews: