manualshive.com logo in svg

ZURN Connected Aqua-FIT Serio Z6950-XL-S-W2, Installation, Operation, Maintenance And Parts Manual

Share
Download
ZURN Connected Aqua-FIT Serio Z6950-XL-S-W2 Installation, Operation, Maintenance And Parts Manual Download Page 4

FV723 Rev.  B 7/29/2020

Page 3

   

 

2.  Install spout to sink using spout base gasket, plastic mounting 

washer, star washer and mounting nut.
Note: Faucet location needs to be within 3 feet radius above 

electrical outlet for ACA configurations.

NOTE

: Before installation, turn off water supplies to existing faucet and remove faucet if replacing an existing device. 

Clean the faucet basin and clear away debris. Flush all supply lines before connecting the faucet. Failure to do so 

may result in debris clogging the inlets and/or internal control and mixing valve

1.  Carefully screw aerator into spout using included tool.  

      Take care to not pinch blue o-ring

3.  Ensure that slot in plastic washer is facing forward.  

Sensor cable should not pass through plastic mounting washer.

4.  Assemble the electronics module

Do not connect the electronic module to spout

Spout Installation Instructions

Summary of Contents for Connected Aqua-FIT Serio Z6950-XL-S-W2

















Reviews:

No comments

Brands by name

Popular brands

Load more brands