background image

LIMITED WARRANTY

All goods sold hereunder are warranted to be free from defects in material and factory workmanship for a period of three years from the

date of purchase. Decorative finishes warranted for one year. We will replace at no costs goods that prove defective provided we are

notified in writing of such defect and the goods are returned to us prepaid at Sanford, NC, with evidence that they have been properly

maintained and used in accordance with instructions. We shall not be responsible for any labor charges or any loss, injury or damages

whatsoever, including incidental or consequential damages. The sole and exclusive remedy shall be limited to the replacement of the

defective goods. Before installation and use, the purchaser shall determine the suitability of the product for his intended use and the

purchaser assumes all risk and liability whatever in connection therewith. Where permitted by law, the implied warranty of merchantability

is expressly excluded. If the products sold hereunder are “consumer products,” the implied warranty of merchantability is limited to a

period of three years and shall be limited solely to the replacement of the defective goods. All weights stated in our catalogs and lists are

approximate and are not guaranteed.

Sensor-Operated Battery-Powered
Lavatory Faucets

®

Aqua-FIT

TM

Serio Series

TM

Sensor-Operated Lavatory Faucets
for Battery or Plug-In Installations.

Installation, Operation, Maintenance,
and Parts Manual

Patented and Patents Pending

Z6950-XL-S

Z6955-XL-S

Z6950-XL-IM-S

Summary of Contents for Aqua-FIT Serio Series










Reviews: