manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 7 OSPFv3 Configuration

Table 7-1 Similarities and Differences Between OSPFv3 LSAs and OSPFv2 LSAs

OSPFv2 LSA

OSPFv3 LSA

Similarities with and

Differences from OSPFv2

LSAs

Router LSA

Router LSA

Network LSA

Network LSA

The name is the same and the

function is similar, except that

the LSA no longer describes

address information but is used

only to describe the topology

structure of the routing area.

Network Summary LSA

Inter Area Prefix LSA

ASBR Summary LSA

Inter Area Router LSA

The function is similar but the

name is different.

AS External LSA

AS External LSA

Both the function and the name

are completely the same.

Link LSA

The LSA is newly added.

-

Intra Area Prefix LSA

The LSA is newly added.

7.2 Configuring OSPFv3

Enabling OSPFv3

To enable OSPFv3, perform the following steps.

Step

Command

Function

1

ZXR10(config)#

ipv6 router ospf

<

process-id

>

Enables the OSPFv3 process.

2

ZXR10(config-ospfv3-process-id)#

router-id

<

router-id

>

Specifies the Router ID for an

OSPFv3 process.

Configuring OSPFv3 Interface Attributes

To configure OSPFv3 interface attributes, perform the following steps.

Step

Command

Function

1

ZXR10(config)#

ipv6 router ospf

<

process-id

>

Enters the interface

configuration mode.

2

ZXR10(config-ospfv3-process-id)#

interface

<

interface-name

>[

area

<

area-id

>]

nstance

<

0-255

>]

Adds an interface to OSPFv3.

7-5

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Link GO-RT-N300 Quick Installation Manual preview
GO-RT-N300
Brand: D-Link Pages: 32
D-Link DXN-W224 Quick Start Manual preview
DXN-W224
Brand: D-Link Pages: 6
D-Link DSR-250N User Manual preview
DSR-250N
Brand: D-Link Pages: 221
D-Link ShareCenter Pro DNS-1200-05 Quick Installation Manual preview
ShareCenter Pro DNS-1200-05
Brand: D-Link Pages: 68
D-Link Express Ethernetwork DI-707P Quick Installation Manual preview
Express Ethernetwork DI-707P
Brand: D-Link Pages: 14
Garland P1GCCAS Installation Manual preview
P1GCCAS
Brand: Garland Pages: 4
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Brand: Paradyne Pages: 45
Navini Networks RIPWAVE 40-00460-00R User Manual preview
RIPWAVE 40-00460-00R
Brand: Navini Networks Pages: 35
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Brand: FS Pages: 19
Waver WAC52N Quick Start Manual preview
WAC52N
Brand: Waver Pages: 36
Tripp Lite N201-007-YW Specification Sheet preview
N201-007-YW
Brand: Tripp Lite Pages: 2
DELTA GROUP LOYTEC LIP‑3ECTC Installation Instructions preview
LOYTEC LIP‑3ECTC
Brand: DELTA GROUP Pages: 4
Belkin F9K1002V1 User Manual preview
F9K1002V1
Brand: Belkin Pages: 42
Valcom VIP-997 Manual preview
VIP-997
Brand: Valcom Pages: 4
ZyXEL Communications GS-1116A Supplementary Manual preview
GS-1116A
Brand: ZyXEL Communications Pages: 1
Vivotek ND9312 User Manual preview
ND9312
Brand: Vivotek Pages: 185
IBM EM78P221/2N Specification preview
EM78P221/2N
Brand: IBM Pages: 70
Tenda W268R User Manual preview
W268R
Brand: Tenda Pages: 74

Brands by name

Popular brands

Load more brands