Zte ZXR10 5900E Series Configuration Manual Download Page 42

Page: 42 / 226

ZXR10 5900E Series Configuration Guide (IPv6)

S1(config)#show ipv6 interface brief

v6_tunnel3

[up/up]

fe80::2d0:d0ff:fe52:abcf

3172::27/64

3.3.2 6to4 Tunnel Configuration Example

Configuration Description

As shown in

Figure 3-6

, suppose S1 and S2 are dual-stack routers whereas PC1 and PC2

are IPv6 hosts. This example describes how to configure a 6to4 tunnel.

Figure 3-6 6to4 Tunnel Configuration Example

Configuration Thought

A 6to4 tunnel is of v6 nature and thus IPv6 needs to be enabled to connect the 6to4 node

prefixed with 2002::/16. The source end of the tunnel is bound with the IPv4 address of

the local router, and no destination address is required. The tunnel address must assume

a 2002::/16 prefix.

Create a 6to4 tunnel, configure IPv6 addresses, and enable IPv6. The first 48 bits of

the tunnel address and the 6to4 sites are of a fixed format and generated according to

the source IPv4 address of the tunnel: Convert the x.x.x.x of the source IPv4 address

of the tunnel into a hexadecimal yyyy:yyyy, and then add 2002::/16 to it to form a 48-bit

prefix 2002:yyyy:yyyy::/48.

Enter the tunnel configuration mode from the global mode, and then enter the 6to4

tunnel interface to be configured.

Configure the tunnel mode and the source address.

Advertise the tunnel route through static routing or BGP4+.

Configuration Commands

S1 configuration:

S1(config)#interface v6_tunnel2

3-8

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands

Zte ZXR10 5900E Series, Configuration Manual

Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands