manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

For a description of the sample output, refer to the following table:

Command Output

Description

DUID

Unique identifier of a client.

IA NA

IA type. IA NA means a temporary address. IA PD means

allocated by a prefix.

IA ID

IA identifier.

T1

Recommended Renew interval.

T2

Recommended Rebind interval.

20.4 DHCPv6 Configuration Examples

20.4.1 DHCPv6 Server Configuration Instance

Configuration Description

As shown in

Figure 20-3

, ZXR10 acts as both DHCP server and the default gateway. The

PC obtains an IP address dynamically through DHCP.

Figure 20-3 DHCPv6 Server Configuration Instance

The configuration requirements of ZXR10 are described below.

l

In global configuration mode, configure an IPv6 address, an IPv6 pool, a DHCPv6

pool and a DHCPv6 policy. Enable DHCPv6 function.

l

In interface configuration mode, configure an IP address and DHCP server mode.

Bind the DHCPv6 policy.

Configuration Thought

1.

Enable IPv6 on the interface and configure an IPv6 address.

2.

Configure an IPv6 address pool and configure related parameters such as the range

of the address pool. The range of the addresses in the pool should be in the same

network segment.

3.

Enable DHCPv6 globally.

4.

Configure DHCPv6 pool. The DHCPv6 pool needs to bind to an IP pool. Configures

DNS, lease time and other parameters.

5.

Configure DHCPv6 policy. The DHCPv6 policy is a policy option. Many priorities are

supported by a name for policy management.

20-10

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link DWL-3150 Install Manual preview
DWL-3150
Brand: D-Link Pages: 8
D-Link DSS-8+ Manual preview
DSS-8+
Brand: D-Link Pages: 22
D-Link DSS-5+ Manual preview
DSS-5+
Brand: D-Link Pages: 20
D-Link DSS-24+ Technical Specifications preview
DSS-24+
Brand: D-Link Pages: 2
D-Link DSS-24+ Manual preview
DSS-24+
Brand: D-Link Pages: 16
D-Link DI-804V Quick Install Manual preview
DI-804V
Brand: D-Link Pages: 12
D-Link DIR-615 - Wireless N Router Installation Manual preview
DIR-615 - Wireless N Router
Brand: D-Link Pages: 13
D-Link Cobra DSL-5300 User Manual preview
Cobra DSL-5300
Brand: D-Link Pages: 124
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link 2Voice + 4SW VoIP Router DVG-1402S User Manual preview
2Voice + 4SW VoIP Router DVG-1402S
Brand: D-Link Pages: 57
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
D-Link SharePort DIR-825 Quick Start Manual preview
SharePort DIR-825
Brand: D-Link Pages: 2
D-Link Amplifi DIR-645 Quick Installation Manual preview
Amplifi DIR-645
Brand: D-Link Pages: 28
D-Link DES-7200 User Manual preview
DES-7200
Brand: D-Link Pages: 100
D-Link DES-3226L Manual preview
DES-3226L
Brand: D-Link Pages: 134

Brands by name

Popular brands

Load more brands