manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

S3(config-bgp)#neighbor 3331::101 remote-as 200

S3(config-bgp)#address-family ipv6

S3(config-bgp-af-ipv6)#neighbor 2010::125 activate

S3(config-bgp-af-ipv6)#neighbor 3331::101 activate

S3(config-bgp-af-ipv6)#neighbor 2010::125 route-reflector-client

S3(config-bgp-af-ipv6)#neighbor 3331::101 route-reflector-client

S3(config-bgp-af-ipv6)#end

9.4.2 BGP4+ General Configuration Example

Configuration Description

This example describes how to configure BGP4+. It involves the practical use of BGP4+,

such as IBGP/EBGP neighbor establishment, routing policy, route redistribution, and

Message Digest 5 Algorithm (

MD5

) encryption.

As shown in

Figure 9-2

, EBGP neighbors are established between S4 and S1, IBGP

neighbors are established between S1 and S2, and multi-hop EBGP neighbors are

established between S2 and S5. S2 and S5 establish an EBGP multi-hop relation through

S3. Before BGP is configured, it is necessary to ensure that the addresses used for

neighbor establishment between the two routers can interwork with each other (via IGP;

IGP configuration is omitted in this example).

Figure 9-2 BGP4+ General Configuration Example

Configuration Thought

1.

Create a BGP4 instance.

2.

Configure BGP4+ neighbors and routing policies.

3.

Configure the redistribution command and enable neighbors to advertise routes.

9-10

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link DWL-3150 Install Manual preview
DWL-3150
Brand: D-Link Pages: 8
D-Link DSS-8+ Manual preview
DSS-8+
Brand: D-Link Pages: 22
D-Link DSS-5+ Manual preview
DSS-5+
Brand: D-Link Pages: 20
D-Link DSS-24+ Technical Specifications preview
DSS-24+
Brand: D-Link Pages: 2
D-Link DSS-24+ Manual preview
DSS-24+
Brand: D-Link Pages: 16
D-Link DI-804V Quick Install Manual preview
DI-804V
Brand: D-Link Pages: 12
D-Link DIR-615 - Wireless N Router Installation Manual preview
DIR-615 - Wireless N Router
Brand: D-Link Pages: 13
D-Link Cobra DSL-5300 User Manual preview
Cobra DSL-5300
Brand: D-Link Pages: 124
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link 2Voice + 4SW VoIP Router DVG-1402S User Manual preview
2Voice + 4SW VoIP Router DVG-1402S
Brand: D-Link Pages: 57
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
D-Link SharePort DIR-825 Quick Start Manual preview
SharePort DIR-825
Brand: D-Link Pages: 2
D-Link Amplifi DIR-645 Quick Installation Manual preview
Amplifi DIR-645
Brand: D-Link Pages: 28
Idis DR-8416 Operation Manual preview
DR-8416
Brand: Idis Pages: 123
Idis DR-6232H Installation Manual preview
DR-6232H
Brand: Idis Pages: 29

Brands by name

Popular brands

Load more brands