manualshive.com logo in svg

Zte ZXHN H268A, Maintenance Management Manual

Share
Download
Zte ZXHN H268A Maintenance Management Manual Download Page 48

Chapter 5 Configure the Local Network

Parameter

Description

Prefix Delegate Type

Prefix delegation type

l

AutoSense

All the available prefixes will be delegated.

l

Manual

One or more prefixes selected manually from all the static

prefixes configured before will be delegated.

13. Click

Apply

button to apply the changes.

– End of Steps –

5.3 Configure the Route

5.3.1 Configure the Routing(IPv4)

The section describes how to configure routing(IPv4).

The gateway needs to be configured for the static mode interface or

IPoA

mode interface

during static routing configuration.

The gateway does not need to be configured for the

PPPoE

mode interface during static

routing configuration.

The relevant information of Internet status includes

Routing Table

and

Static Routing

.

Prerequisite

Before configuring static routing, make sure that the IPv4 WAN connection is created.

Steps

Routing Table

1.

On the main page of the ZXHN H268A, select

Local Network > Routing > IPv4

to

open the

Routing Table

page, as shown in

Figure 5-18

.

Figure 5-18 Routing Table

2.

Click

Refresh

to refresh the informations.

Static Routing

3.

Click

Static Routing

to open the

Static Routing

page, as shown in

Figure 5-19

.

5-13

SJ-20150916162339-007|2017-02-16 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXHN H268A

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands