Zte ZXHN H2640 Maintenance Management Manual Download Page 16

Page: 16 / 116

ZXHN H2640 Maintenance Management Guide(TIM)

4-2

SJ-20200714160642-002 | 2020-07-27(R1.0)

Figure 2-2 The Rear Panel

Interface/

Button

Function

WiFi

Wi-Fi dual-interfaces On/Off button.

WPS

WPS Push Button, press this button to enable or disable the WPS function.

Power

Power supply port, it is connected to the power adapter.

Reset

Reset pinhole, it is used to reset the configuration to factory default settings.

Tel1

–Tel2

RJ-11 port, it is used to connect to the analog telephone.

USB2

USB3.0 host port in right panel.

LAN1-LAN3

RJ-45 port, it is used to connect the modem to computer , STB or other network

devices.

LAN4/WAN

RJ-45 port, it is used to connect to the uplink Ethernet access network.

DSL

RJ-14 port, it is used to connect to the uplink ADSL, VDSL or VDSL Bonding access

network.

Figure 2-3

shows the interfaces on the side panel of the ZXHN H2640.

Side panel

Summary of Contents for ZXHN H2640





















































































































Search results

Summary of Contents for ZXHN H2640

Reviews:

Related manuals for ZXHN H2640

Brands by name

Popular brands

Zte ZXHN H2640, Maintenance Management Manual

Search results

Summary of Contents for ZXHN H2640

Reviews:

Related manuals for ZXHN H2640

Brands by name

Popular brands