Zte ZXHN H1600 Maintenance Management Manual Download

Page: 95 / 109

ZXHN H1600 Maintenance Management Guide

Figure 8-4 Device Management Page

2. On this page, you can perform the following operations:



Click

Reboot

to reboot the ZXHN H1600 device.



Click

Factory Reset

to restore the factory default settings.

8.3.2 Upgrade Software

This procedure introduces how to upgrade Software.

Prerequisite

Make sure that the upgrade file is ready.

Steps

1. On the main page of the ZXHN H1600, select

Management&Diagnosis > System

Management > Software Upgrade

to the

Software Upgrade

page, see

Figure 8-5

Figure 8-5 Software Upgrading Page

2. Click

Browse

to select the upgrade version file.

8-4

SJ-20200218145027-006 | 2021-03-04(R1.0)

Summary of Contents for ZXHN H1600














































































































Search results

Summary of Contents for ZXHN H1600

Reviews:

Related manuals for ZXHN H1600

Brands by name

Popular brands

Zte ZXHN H1600, Maintenance Management Manual

Search results

Summary of Contents for ZXHN H1600

Reviews:

Related manuals for ZXHN H1600

Brands by name

Popular brands