Zte ZXHN H1600 Maintenance Management Manual Download

Page: 106 / 109

8 Configure the Management and Diagnosis

Steps

1. On the main page of the ZXHN H1600, select

Management&Diagnosis > MAC Ta-

ble

to the

MAC Table

page, see

Figure 8-20

Figure 8-20 MAC Table Page

2. Click

Refresh

button to refresh information.

8.10 Configure the IPv6 Switch

This procedure describes how to enable or disable IPv6 support for the ZXHN H1600.

Steps

1. On the main page of the ZXHN H1600, select

Management&Diagnosis > IPv6

Switch

to the

IPv6 Switch

page, see

Figure 8-21

Figure 8-21 IPv6 Switch Page

2. To disable IPv6 support, set IPv6 Function to

Off

, and click

Apply

Note

The configuration takes effective after the device is restarted.

SJ-20200218145027-006 | 2021-03-04(R1.0)

8-15

Summary of Contents for ZXHN H1600














































































































Search results

Summary of Contents for ZXHN H1600

Reviews:

Related manuals for ZXHN H1600

Brands by name

Popular brands

Zte ZXHN H1600, Maintenance Management Manual

Search results

Summary of Contents for ZXHN H1600

Reviews:

Related manuals for ZXHN H1600

Brands by name

Popular brands