Zte ZXA10 C300 Configuration Manual Download Page 81

Page: 81 / 301

Chapter 6 IPTV Configuration

6.2 Configuring the MLD MVLAN

The MLD MVLAN is the VLAN that carries the MLD multicast data, which includes the

service VLAN, source port, receive port, and multicast group.

Configuration Data

Table 6-2

lists the configuration data of the

MLD MVLAN

Table 6-2 Configuration Data of the MLD MVLAN

Item

Data

MLD

Enable

Span VLAN function

Enable

MVLAN ID

200

MVLAN working mode

Proxy

MVLAN host version

MLDv1

Multicast group IP address

ff1e::0101–ff1e::0103

Multicast source port

gei_1/21/1

Multicast receive port

ONU interface: gpon-onu_1/5/1:1

Virtual port ID: 1

Steps

In uplink interface configuration mode, configure the uplink port VLAN.

ZXAN(config)#interface gei_1/21/1

ZXAN(config-if)#switchport vlan 200 tag

ZXAN(config-if)#exit

In ONU interface mode, configure the service port VLAN.

ZXAN(config)#interface gpon-onu_1/5/1:1

ZXAN(config-if)#service-port 1 vport 1 user-vlan 200 vlan 200

ZXAN(config-if)#exit

Enable MLD globally.

ZXAN(config)#mld enable

Enable MLD span VLAN function.

ZXAN(config)#mld span-vlan enable

Configure the MVLAN.

ZXAN(config)#mld mvlan 200

Configure the MVLAN working mode.

ZXAN(config)#mld mvlan 200 work-mode proxy

Configure the MVLAN host version.

ZXAN(config)#mld mvlan 200 host-version v1

6-5

SJ-20130520164529-007|2013-06-30 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXA10 C300














































































































































































































































































































Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands

Zte ZXA10 C300, Configuration Manual

Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands