Zte ZXA10 C300 Configuration Manual Download Page 20

Page: 20 / 301

ZXA10 C300 Configuration Manual (CLI)

ZXAN(config)#add-shelf shelfno 1 shelftype ETSI_SHELF

Note:

The ZXA10 C300 supports only one shelf currently, and thus

shelfno

can only be 1.

(Optional) Query the shelf configuration.

ZXAN(config)#show shelf

Rack

Shelf

ShelfType

CleiCode

Serial-Number

------------------------------------------------------------------------------

ETSI_SHELF

UNKNOWN

10011001C3000090

000000000000

– End of Steps –

Result

After the shelf is added, the system will automatically add two switching and control cards.

ZXAN(config)#show card

Rack Shelf Slot CfgType RealType Port

HardVer SoftVer

Status

----------------------------------------------------------------------------

SCXN

120900

V2.0.0

INSERVICE

SCXN

120900

V2.0.0

STANDBY

1.3.3 Adding a Card

When replacing the card type during commissioning or capacity expansion, you need to

add a card.

Context

Table 1-3

describes the card configurations for a 19-inch shelf.

Table 1-3 Card Configurations for a 19-Inch Shelf

Slot Number

Card Type

0/1

Power card

2–9

PON interface card, TDM interface card, Ethernet interface card, and

P2P interface card

10/11

Switching and control card

12–17

PON interface card, TDM interface card, Ethernet interface card, and

P2P interface card

Common interface card

19/20

Uplink card

1-10

SJ-20130520164529-007|2013-06-30 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXA10 C300














































































































































































































































































































Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands

Zte ZXA10 C300, Configuration Manual

Search results

Summary of Contents for ZXA10 C300

Reviews:

Related manuals for ZXA10 C300

Brands by name

Popular brands