manualshive.com logo in svg

Zte WF723CA, User Manual, Page: 29 / 30

Share
Download
Zte WF723CA User Manual Download Page 29

29 

 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux 

appareils  radio  exempts  de  licence.  L'exploitation  est  autorisée  aux  deux 

conditions suivantes:   

(1) l'appareil ne doit pas produire de brouillage, et   

(2)  l'utilisateur  de  l'appareil  doit  accepter  tout  brouillage  radioélectrique  subi, 

même si le brouillage est susceptible d'en 

 

This Class B digital apparatus complies with Canadian ICES-003. 

Cet  appareil  numérique  de  la  classe  B  est  conforme  à  la  norme  NMB-003  du 

Canada. 

 

IC: 5200E-WF723 

 

ISED RF Exposure Statement 

This  device  complies  with  ISED  RSS-102  RF  exposure  limits  set  forth  for  an 

uncontrolled  environment.  In  order  to  avoid  the  possibility  of  exceeding  the  IC 

RSS-102 RF exposure limits, human proximity to the antenna shall not be less 

than 20cm (8 inches) during normal operation. 

Cet  appareil  est  conforme  aux  limites  d'exposition  aux  rayonnements  de  la 

CNR-102 définies pour un environnement non contrôlé. Afin d'éviter la possibilité 

Summary of Contents for WF723CA































Reviews:

No comments