ZOTYE JNJ7155 Quick Start Manual Download Page 38 | Manualshive

Page: 38 / 290

background image

036

Air bag

Causes that trigger the air bag

When the vehicle collides with an obstacle, the air bag expands
quickly if the trigger condition is met. The condition include collision
energy, accident type, collision angle, obstacle and vehicle speed. The
air bag may not be triggered even the vehicle is seriously damaged in
an accident.

Description!

Smoke  is  seen  when  the  air  bag  expands.  The  smoke  is
non-poisonous and does not mean the vehicle is on fire; however,
you shall not breathe in the smoke too much, because it stimulates
your  respiratory  tract  and  even  leads  to  suffocation.  One  who  is
suffering  from  diseases  of  respiratory  tract  or  dyspnea,  please
leave the vehicle when it is safe to where the air is fresh.

«
...
36
37
38
39
40
...
»

Summary of Contents for JNJ7155



































































































































































































































































































Reviews:

No comments

Related manuals for JNJ7155

Brand: Daihatsu Pages: 340

Brand: Warrior Products Pages: 2

Brand: Pivot Pages: 4

Brand: Simplicity Pages: 10

Brand: Scion Pages: 24

Brand: MULTILIFT Pages: 62

INDICA eV2 XETA CNG

Brand: TATA Motors Pages: 24

Brand: PAC Pages: 5

Brand: Percon Pages: 49

Brand: GYS Pages: 32

Brand: TomTom Pages: 22

HOLLANDIA 700 - 20 Series

Brand: Webasto Pages: 30

Brand: Buick Pages: 58

Brand: Vauxhall Pages: 4

Brand: Lincoln Pages: 364

Brand: ULTIMATE SPEED Pages: 132

Brand: Lincoln Pages: 370

Brand: TrailFX Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands